Home › ENGINE ยท 5L-E › ENGINE MECHANICAL › TIMING BELT

TIMING BELT > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation.



2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A114241
  1. Remove the reservoir cap and, using a wrench, remove the vent plug.



  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A114242E01



3. DISCONNECT RADIATOR HOSE INLET


4. REMOVE FAN SHROUD


    A114244
  1. Remove the 3 bolts and oil reservoir.

  1. Disconnect the No. 1 and No. 2 water by-pass hoses from the tank upper and lower.

  1. Remove the bolt and radiator reservoir.

  1. Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the vane pump V belt, cooler compressor V belt and fan and generator V belt (Click here).

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.



5. REMOVE VANE PUMP V BELT


    A121092E01
  1. Loosen bolt A and nut B, and remove the V belt.



6. REMOVE COOLER COMPRESSOR V BELT (w/ Air Conditioning System)


    A121093E01
  1. Loosen nut A and bolt B, and remove the V belt.



7. REMOVE FAN & GENERATOR V BELT (w/o Air Conditioning System)


    A142830E01
  1. Loosen the bolts A and B, and remove the V belt.



8. REMOVE FAN & GENERATOR V BELT (w/ Air Conditioning System)


    A115632E01
  1. Loosen the bolts A and B.

  1. Loosen adjusting bolt C, and remove the V belt.



9. DISCONNECT COMPRESSOR AND MAGNET CLUTCH (w/ Air Conditioning System)


    A123646
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.



10. REMOVE COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)


    A112016E01
  1. Remove the bolt and spacer.



    A121135E01
  1. Remove the 4 bolts and compressor mounting bracket.



11. REMOVE VANE PUMP DRIVE PULLEY


    A112013
  1. w/o Air Conditioning System:
    Remove the 4 bolts, vane pump drive pulley and vane pump drive pulley spacer.

  1. w/ Air Conditioning System:
    Remove the 4 bolts and vane pump drive and No. 2 crankshaft pulleys.



12. REMOVE CRANKSHAFT PULLEY


    A058720E01
  1. Using SST, remove the pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A058719E01
  1. Using SST, remove the pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)
    09950-60010   (09951-00490)
    09950-40011   (09957-04010)



13. REMOVE TIMING BELT COVER SUB-ASSEMBLY


    A112017
  1. Remove the 11 bolts, washers, timing belt cover and 2 gaskets.



14. REMOVE TIMING BELT GUIDE
  1. Remove the timing belt guide.



15. SET NO. 1 CYLINDER TO TDC / COMPRESSION


    A058728E02
  1. Using the crankshaft pulley bolt, align its groove with the timing pointer by turning the crankshaft clockwise.



    A058729E01
  1. Check that the timing marks of the camshaft timing pulley and No. 2 timing belt cover are aligned.
    If not, turn the crankshaft 1 revolution (360°).



16. REMOVE TIMING BELT

HINT:
A058721E01
If reusing the timing belt, draw a direction arrow on the timing belt (in the direction of engine revolution), and place matchmarks on the pulleys and timing belt.



    A058730E02
  1. Turn the crankshaft 90° counterclockwise, and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.

    NOTICE:
    If the timing belt is disengaged, having the crankshaft timing pulley at the wrong angle can cause the piston head and valve head to come into contact with each other when removing the camshaft timing pulley, causing damage. So always set the crankshaft pulley at the correct angle.



    A058731E01
  1. Loosen the No. 1 timing belt idler bolt (A), and shift the idler to the left as far as possible.

  1. Temporarily tighten the pulley bolt (A), and then relieve the timing belt tension.

  1. Remove the timing belt.