Home › TRANSMISSION · A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 2KD-FTV)

DTC    P0722    Output Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the TCM. The TCM determines the vehicle speed based on these signals. An AC voltage is generated in the speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the TCM.
The gear shift point and lock-up timing are controlled by the TCM based on the signals from this vehicle speed sensor and the throttle position sensor signal.

DTC Code
DTC Detection Condition
Trouble Area
P0722
  1. All conditions below are detected 500 times or more continuously (2-trip detection logic):
    1. No signal from speed sensor SP2 is input to TCM while 4 pulses of No. 1 vehicle speed sensor signal are sent
    2. Vehicle speed is 9 km/h (6 mph) or more for at least 4 sec.
    3. Park/neutral position switch is off
  1. Open or short in speed sensor SP2 circuit
  2. Speed sensor SP2
  3. TCM
  4. Automatic transmission (clutch, brake, gear, etc.)
Reference: Inspect using an oscilloscope.
Check the waveform of the TCM connector.

Standard:
Terminal No. (Symbol)
Tool Setting
Condition
Specified Condition
T19-30 (SP2+) - T19-29 (SP2-)
2 V/DIV., 20 msec./DIV.
Vehicle speed 20 km/h (12 mph)
Refer to illustration

C170571E02

MONITOR DESCRIPTION

The output speed sensor SP2 monitors the output shaft speed. The TCM controls the gear shift point and lock-up timing based on the signals from the output speed sensor SP2 and throttle position sensor.
If the TCM detects no signal from the output speed sensor SP2 even while the vehicle is moving, it will conclude that there is a malfunction of the output speed sensor SP2. The TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM


C239151E17


INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the tester, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph)
    (output shaft speed is equal to vehicle speed)
    -

    HINT:
    1. SPD (SP2) is always 0 while driving:
      Open or short in the sensor or circuit.
    2. The SPD (SP2) value displayed on the intelligent tester is much lower than the actual vehicle speed:
      Sensor trouble, improper installation, or intermittent connection trouble in the circuit.

1.INSPECT SPEED SENSOR SP2 INSTALLATION


    C211922E01
  1. Check the speed sensor SP2 installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.

    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT



NG
SECURELY INSTALL OR REPLACE SPEED SENSOR SP2
OK


2.INSPECT SPEED SENSOR SP2


    C206284E04
  1. Disconnect the T8 speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Speed Sensor SP2)



NG
REPLACE SPEED SENSOR SP2
OK


3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR SP2 - TCM)


    C274533E48
  1. Disconnect the T19 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T19-30 (SP2+) - T19-29 (SP2-)
    20°C (68°F)
    560 to 680 Ω
    T19-30 (SP2+) - Body ground
    Always
    10 kΩ or higher
    T19-29 (SP2-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to TCM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM