ECD SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Start the engine.
Turn the intelligent tester on.
![]() |
Enter the following menus: Powertrain / Engine and ECT / Data List.
Check the values by referring to the table below.
| Engine Control |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Calculate Load | Load calculated by ECM/ Min.: 0%, Max.: 100% |
| Calculated by ECM | Malfunction in which turbo pressure or Mass Air Flow decreases |
| Diagnostic Note: Calculated load = (Final injection volume / max. injection volume at current engine speed) x 100. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| MAF | Air flow rate from mass air flow meter/ Min.: 0 gm/s, Max.: 400 gm/s |
| Sensor output (mass air flow meter) |
|
| Symptoms when out of range: Rough idling | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 51199 rpm |
| Sensor output (crankshaft position sensor) |
|
| Diagnostic Note: When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| MAP | Absolute pressure inside intake manifold/ Min.: 0 kPa, Max.: 255 kPa |
| Sensor output (manifold absolute pressure sensor) |
|
| Symptoms when out of range: Lack of power | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | Sensor output (speed sensor) |
|
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Coolant Temp | Engine coolant temperature/ Min.: -40°C, Max.: 140°C | After warming up engine: 70 to 90°C (158 to 194°F) | Sensor output (engine coolant temperature sensor) |
|
| Symptoms when out of range: Difficulty starting when engine is cold, rough idle, black smoke, lack of power | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Intake Air | Intake air temperature/ Min.: -40°C, Max.: 140°C | Equivalent to temperature at location of mass air flow meter | Sensor output (intake air temperature sensor [built into mass air flow meter]) | Intake air temperature sensor |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Initial Engine Coolant Temp | Initial engine coolant temperature/ Min.: -40°C, Max.: 120°C | Engine coolant temperature when engine started | Sensor output when engine started | - |
| Diagnostic Note: For freeze frame data, this tells whether the malfunction happened at a cold start or with a warm engine. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Initial Intake Air Temp | Initial intake air temperature/ Min.: -40°C, Max.: 120°C | Intake air temperature when engine started | Sensor output when engine started | - |
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Intake Air Temp (Turbo) | Intake air temperature after intercooler/ Min.: -40°C, Max.: 190°C | 70°C (158°F) or less | Sensor output (intake air temperature sensor after intercooler) | Decreased cooling efficiency of intercooler (contamination, clogging) |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pre Glow | Pre-glow operation/ ON or OFF | - | Result of ECU calculations | - |
| Diagnostic Note: This is the ECM command. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| After Glow | After-glow operation/ ON or OFF | - | Result of ECU calculations | - |
| Diagnostic Note: This is the ECM command. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Alternate Duty Ratio | Alternator generation duty ratio/ Min.: 0%, Max.: 100% |
| Duty value from ALT terminal |
|
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Starter Signal | Starter signal/ ON or OFF | ON: Cranking | - |
|
Symptoms when out of range:
| ||||
| Diagnostic Note: Ignition switch (STA) output:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| A/C Signal | A/C (Air Conditioner) signal/ ON or OFF | ON: A/C on | A/C operation signal output from A/C amplifier
|
|
| Symptoms when out of range: OFF malfunction (OFF even when A/C switch is turned on):
| ||||
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Stop Light Switch | Stop light switch/ ON or OFF |
| Switch output (stop light switch) |
|
| Symptoms when out of range: Stop light switch malfunction DTC P0504 is stored | ||||
| Diagnostic Note: Stop light switch (STP) operation condition:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Immobiliser Communication | Immobiliser communication/ ON or OFF |
| - |
|
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Clutch Switch | Clutch switch/ ON or OFF | ON: Clutch pedal depressed | Switch output (clutch switch) | - |
| Symptoms when out of range: The cruise control, pilot quantity learning, etc. may not function properly or may not function at all. | ||||
| Diagnostic Note: When this item displays "OFF" with the clutch pedal depressed, the shock when accelerating and decelerating the vehicle becomes larger and pilot quality learning cannot be performed. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Neutral Position SW Signal | Neutral position switch status/ ON or OFF | ON: Shift lever in neutral | Switch output (neutral position switch) | - |
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Battery Voltage | Battery voltage/ Min.: 0 V, Max.: 15 V | 11 to 14 V | - | - |
| Symptoms when out of range: If 5 V or less, starting becomes difficult | ||||
| Diagnostic Note: If 11 V or less, characteristics of some electrical components change. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Atmosphere Pressure | Atmospheric pressure value/ Min.: 50 kPa, Max.: 120 kPa | Actual atmospheric pressure | Sensor output (atmospheric pressure sensor [built into ECM]) | Atmospheric pressure sensor itself has failed (atmospheric pressure sensor is inside the ECM) |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| ACT VSV | A/C cut status for Active Test/ ON or OFF | - | - | - |
| Diagnostic Note: "Control the A/C Cut Signal" Active Test support data. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| TC and TE1 | TC and TE1 connection status for Active Test/ ON or OFF | - | - | - |
| Diagnostic Note: When the "Connect the TC and TE1" Active Test is performed, the system behaves as if TC and CG were connected. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| # Codes (Include History) | Number of codes/ Min.: 0, Max.: 255 | - | - | - |
| Diagnostic Note: Number of DTCs appearing at least once during the last 40 times the vehicle was warmed up. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Check Mode | Check mode/ ON or OFF | ON: Check mode on | - | - |
| Diagnostic Note: Check Mode: The mode in which certain DTCs can be detected more easily and with higher sensitivity. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| SPD Test Result | Check mode result for vehicle speed sensor/ Compl or Incompl | - | - | - |
| Diagnostic Note: SPD Test Result: Check mode result for the vehicle speed sensor. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| MIL | MIL status/ ON or OFF | OFF: MIL off | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Engine Run Time | Engine run time/ Min.: 0 sec., Max.: 65535 sec. | Time after the ignition switch turned on | Result of ECU calculations (using the engine speed) | - |
| Diagnostic Note: Time passed since the ignition switch was turned on. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Time after DTC Cleared | Time after DTC cleared/ Min.: 0 min., Max.: 65535 min. | Time after DTCs cleared | - | - |
| Diagnostic Note: Time elapsed since the DTCs were cleared (or shipment from the factory). | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Distance from DTC Cleared | Distance driven after DTC cleared/ Min.: 0 km, Max.: 65535 km | Distance driven after DTCs cleared | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Warmup Cycle Cleared DTC | Warmup cycles after DTC cleared/ Min.: 0, Max.: 255 | - | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| OBD Requirements | Identifying OBD requirement | - | - | - |
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Number of Emission DTC | Number of emissions-related DTCs | - | - | |
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Engine Start Time | Engine start time/ Min.: 0 ms, Max.: 267000 ms | - | - | - |
| Diagnostic Note: Time necessary for the engine to start. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Accel Position | Accelerator position status/ Min.: 0%, Max.: 100% |
|
| - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Accel Sens. No.1 Volt % | Accelerator position No. 1/ Min.: 0%, Max.: 100% |
| Sensor output (Accelerator pedal position sensor) | - |
| Diagnostic Note: Read value with ignition switch to ON (do not start engine) | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Accel Sens. No.2 Volt % | Accelerator position No. 2/ Min.: 0%, Max.: 100% |
| Sensor output (Accelerator pedal position sensor) | - |
| Diagnostic Note: Read value with ignition switch to ON (do not start engine) | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Swirl Control Valve VSV | Status of VSV for swirl control valve/ ON or OFF | ON: Idling | - | - |
| Diagnostic Note: - | ||||
| Compression |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Engine Speed of Cyl #1 Engine Speed of Cyl #2 Engine Speed of Cyl #3 Engine Speed of Cyl #4 | Engine speed for No. 1 to No. 4 cylinder/ Min.: 0 rpm, Max.: 6000 rpm | Engine speeds of all cylinders almost same | - | Cyl #1 compression goes down |
| Symptoms when out of range: When the engine speeds of all cylinders are not equal, idling will be rough. | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Av Engine Speed of All Cyl | Engine speed for all cylinders/ Min.: 0 rpm, Max.: 6000 rpm | - | - | - |
Diagnostic Note:
| ||||
| Vehicle Information |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Model Code | Model code | - | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Engine Type | Engine type | - | - | - |
| Diagnostic Note: Identifying engine type: 2KD-FTV | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Cylinder Number | Cylinder number/ Min.: 0, Max.: 255 | - | - | - |
| Diagnostic Note: Identifying cylinder number: 4 | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Transmission Type | Transmission type/ MT or ECT 4th | - | - | - |
| Diagnostic Note: Identifying transmission type: MT (Manual transmission) | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Destination | Destination | - | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Model Year | Model year/ Min.: 1900, Max.: 2155 | - | - | - |
| Diagnostic Note: Identifying model year: 20## | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| System Identification | System identification | - | - | - |
| Diagnostic Note: Identifying engine type: Diesel | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| VN Turbo Type | VN turbo type/ Not Avl, Commo, Vacuum, CAN Com or DC | Commo | - | - |
| Diagnostic Note: Indicates the VN turbo vane actuation method.
| ||||
| Diesel Injection |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Target Common Rail Pressure | Target common rail pressure/ Min.: 0 kPa, Max.: 250000 kPa | 30000 to 180000 kPa when engine running | Target common rail pressure (ECU calculated value) | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Fuel Press | Fuel pressure/ Min.: 0 kPa, Max.: 250000 kPa | Idling: 25000 to 35000 kPa | Sensor output (fuel pressure sensor) |
|
| Symptoms when out of range: Difficult to start, poor driveability, lack of power, abnormal combustion noise | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Common Rail Pres Sens 2 | Fuel pressure/ Min.: 0 kPa, Max.: 250000 kPa | Idling: 25000 to 35000 kPa | Sensor output (fuel pressure sensor) |
|
| Symptoms when out of range: Poor driveability, lack of power, abnormal combustion noise | ||||
| Diagnostic Note: This is a backup output value from the fuel pressure sensor. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Target Pump SCV Current | Final pump current target value/ Min.: 0 mA, Max.: 4000 mA | Idling: 923 to 1123 mA | Target value control (pump current) |
|
| Symptoms when out of range: Difficulty starting, lack of power or rough idling | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Inj. FB Vol. for Idle | Idle stability status integral control volume/ Min.: -80 mm3/st, Max.: 79 mm3/st | -10 to 10 mm3/st | - | - |
| Symptoms when out of range: Engine friction problem, compression problem or injector breakdown | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Injection Volume | Injection volume/ Min.: 0 mm3/st, Max.: 1279.98 mm3/st | Idling: 3.0 to 10 mm3/st | Calculated value | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Inj Vol Feedback Learning | Injection volume feedback learning value: Min.: -10 mm3/st, Max.: 9.92 mm3/st | - | - | - |
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Injector Memory Error | Injector Memory Error/ No Error or Error | No Error | Calculated value | - |
| Symptoms when out of range: Rough idling, poor driveability, black smoke, white smoke, combustion noise | ||||
| Diagnostic Note: If the injector compensation codes are not input into the new ECM, or if a injector compensation code of a different injector model or a compensation code representing a value which exceeds the compensation setting range is input into the new ECM, DTC P1601 is stored and "Injector Memory Error" displays "Error". | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Reju Pilot Quantity Learning | Pilot quantity learning prohibition state/ READY or NG | - | Calculated value | - |
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pilot Quantity Learning | State of "Pilot Quantity Learning"/ Standby / Wait / Learn / Stop / Comple | - | Calculated value | - |
| Diagnostic Note: If "Pilot Quantity Learning" is incomplete, the MIL illuminates and DTC P1601 is stored. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Fuel Return Temp | Fuel return temperature/ Min.: -40°C, Max.: 140°C | Idling after engine warmed-up: 35 to 85°C | - | - |
| Diagnostic Note: If the "Fuel Return Temp" value is not between 55°C (131°F) and 130°C (266°F), "Pilot Quantity Learning" is prohibited. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Injection Pressure Correction | Injection pressure feedback compensation volume/ Min.: -500 mm3/st, Max.: 780 mm3/st | -400 to 400 mm3/st at standard temperature | Calculated value |
|
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Injection Feedback Val #1 Injection Feedback Val #2 Injection Feedback Val #3 Injection Feedback Val #4 | Injection volume correction for each cylinder/ Min.: -10 mm3/st, Max.: 10 mm3/st | Idling: -3.0 to 3.0 mm3/st | Learned value |
|
| Symptoms when out of range: Rough idling, black smoke, white smoke, poor driveability, lack of power, abnormal combustion noise, difficult to start | ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pilot 1 Injection Period | Pilot 1 injection period/ Min.: 0 μs, Max.: 65535 μs | Idling: 350 to 450 μs | Calculated value | - |
| Symptoms when out of range: Combustion noise, poor driveability, white smoke | ||||
| Diagnostic Note: Check to see if "Pilot 1 Injection Period" is not zero when symptoms occur. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pilot 2 Injection Period | Pilot 2 injection period/ Min.: 0 μs, Max.: 65535 μs | Idling: 350 to 450 μs | Calculated value | - |
| Symptoms when out of range: Combustion noise, poor driveability, white smoke | ||||
| Diagnostic Note: Check to see if "Pilot 2 Injection Period" is not zero when symptoms occur. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Main Injection Period | Main injection period/ Min.: 0 μs, Max.: 65535 μs | Idling: 450 to 640 μs | Calculated value | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| After Injection Period | After injection period/ Min.: 0 μs, Max.: 65535 μs | - | Calculated value | - |
| Diagnostic Note: Check to see if "After Injection Period" is not zero when the following symptoms occur: Black smoke, poor driveability. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pilot 1 Injection Timing | Pilot 1 injection timing/ Min.: -70°CA, Max.: 20°CA | Idling after engine warmed up and vehicle under normal atmospheric pressure: -14.2 to -13.2°CA | Calculated value | - |
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pilot 2 Injection Timing | Pilot 2 injection timing/ Min.: -50°CA, Max.: 20°CA | Idling after engine warmed up and vehicle under normal atmospheric pressure: -7.7 to -6.7°CA | Calculated value | - |
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Main Injection Timing | Main injection timing/ Min.: -90°CA, Max.: 90°CA | Idling after engine warmed up and vehicle under normal atmospheric pressure: 2 to 8°CA | Calculated value | - |
| Diagnostic Note: Use "Main Injection Timing" to check poor drivability when the following symptoms are present: Bad injection timing, black smoke, and white smoke. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| After Injection Timing | After injection timing/ Min.: -10°CA, Max.: 50°CA | - | Calculated Value | - |
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Fuel Temperature | Fuel temperature/ Min.: -40°C, Max.: 140°C | Actual fuel temperature | Sensor output (fuel temperature sensor) | - |
| Diagnostic Note: After fully cold soaking the engine, the fuel temperature is the same as the outside air temperature. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Pressure Discharge Valve | Pressure discharge valve operation/ ON or OFF | ON: Pressure discharge valve open | - | - |
| Diagnostic Note: This is the ECM command. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Idle Injection Volume (Min) | Idle minimum injection volume/ Min.: 0 mm3/st, Max.: 39.8 mm3/st | - | - | - |
| Diagnostic Note: This is the ECM command. | ||||
| EGR System |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Target EGR Position | EGR valve target opening amount/ Min.: 0%, Max.: 100% | Idling after engine warmed up: 0 to 98% | ECU-calculated value based on sensors (mass air flow meter, manifold absolute pressure sensor, intake air temperature [built into mass air flow meter], etc.) | - |
Symptoms when out of range:
| ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Actual EGR Valve Pos. | EGR valve position/ Min.: 0%, Max.: 100% | Idling after engine warmed up: 0 to 98% | Calculated from EGR valve position sensor | |
Symptoms when out of range:
| ||||
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| EGR Lift Sensor Volt % | EGR lift position/ Min.: 0%, Max.: 100% | Idling after engine warmed up: 0 to 98% | Calculated from EGR valve position sensor | |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| EGR Operation Prohibit | EGR operation prohibition/ OK or NG | OK: Possible to perform "Control the EGR Step Position" Active Test | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| EGR Close Learn Val. | EGR valve lift volume learned value/ Min.: 0 V, Max.: 5 V | 0 to 1 V | EGR valve position sensor value when EGR valve fully closed | - |
| Symptoms when out of range: - | ||||
| Diagnostic Note: When the value is at the upper or lower limit of the normal range, it is possible that a foreign object is lodged in the EGR valve seat area. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| EGR Close Lrn. Val. | EGR fully closed position learned value/ Min.: 0 V, Max.: 5 V | 0 to 1 V | EGR valve position sensor value when EGR valve fully closed | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| EGR Close Lrn. Status | EGR valve fully closed position learning status/ OK or NG | OK | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| EGR Cut VSV | EGR Cut VSV/ ON or OFF | - | - | - |
| Diagnostic Note: - | ||||
| Diesel Throttle System |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Target Throttle Position | Target throttle position Min.: -128%, Max.: 127% |
| Value calculated by ECM | - |
| Diagnostic Note: If there is a malfunction of the throttle actuator, compare the target and actual throttle position values for troubleshooting. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Actual Throttle Position | Actual diesel throttle position/ Min.: -20%, Max.: 120% | Idling after engine warmed-up: 55 to 90% | - | - |
Symptoms when out of range:
| ||||
| Diagnostic Note: Closing percentage of the throttle valve.
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Throttle Close Learning Val. | Throttle fully closed position learned value/ Min.: 0 deg, Max.: 84 deg | 11 to 21 deg | - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Diesel Throttle Learn Status | Diesel throttle learning history/ OK or NG | OK | - | - |
Diagnostic Note:
| ||||
| VN Turbo System |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Target Booster Pressure | Target booster pressure/ Min.: 0 kPa, Max.: 320 kPa | Driving vehicle on level surface at 3000 rpm with full load: 150 to 250 kPa | Value calculated by ECM | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| VN Turbo Command | VN turbo command value/ Min.: 0%, Max.: 100% | 0 to 100% | Controls the VN turbo vane opening position | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| VN Turbo Max Angle | VN turbo maximum opening amount/ Min.: 0%, Max.: 100% | 100%
| - | - |
Diagnostic Note:
| ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| VN Turbo Min Angle | VN turbo minimum opening amount/ Min.: 0%, Max.: 100% | 0%
| - | - |
Diagnostic Note:
| ||||
| Diesel Starting |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Engine Speed (Starter Off) | Engine speed when starter off/ Min.: 0 rpm, Max.: 1594 rpm | - | - | - |
| Diagnostic Note: Engine speed immediately after starting the engine. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Starter Count | Starter on count/ Min.: 0, Max.: 255 | - | - | - |
| Diagnostic Note: Number of times the starter turned on from the time the ignition switch was turned to on. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Run Dist of Previous Trip | Distance driven during previous trip/ Min.: 0 km, Max.: 261 km | - | - | - |
| Diagnostic Note: Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
| ||||
| Diesel Rough |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Electric Duty Feedback Value | Electric load feedback value/ Min.: 0 mm3/st, Max.: 39.8 mm3/st | 0 to 10 mm3/st | - | - |
| Diagnostic Note: Expected injection volume increase after the electrical load turns from off to on. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| A/C Duty Feedback Value | A/C load feedback value/ Min.: 0 mm3/st, Max.: 39.8 mm3/st | 0 to 10 mm3/st | - | - |
| Diagnostic Note: Expected injection volume increase after the A/C turns from off to on. | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| PS Duty Feedback Value | Power steering load feedback value/ Min.: 0 mm3/st, Max.: 39.8 mm3/st | 0 to 10 mm3/st | - | - |
| Diagnostic Note: Expected injection volume increase after the power steering turns from off to on. | ||||
| AT (for Automatic Transmission) |
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Received MIL from ECT | MIL status from ECT/ ON or OFF | ON: MIL ON | - | - |
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| Shift Position Sig. from ECT | Shift position signal from ECT/ 1st, 2nd, 3rd, 4th, 5th or 6th | - | - | - |
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| A/T Oil Temp from ECT | ATF temperature from ECT/ Min.: -40°C, Max.: 215°C | With engine cold: Equal to ambient temperature | - | - |
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| SPD (NO) | Output shaft speed/ Min.: 0 rpm, Max.: 12750 rpm | - | - | - |
| Diagnostic Note: - | ||||
| Tester Display | Measurement Item/Range | Normal Condition | Type | Cause of Out of Range |
| ECT Lock Up | Lock-up/ ON or OFF | ON: Lock-up operating | - | - |
| Diagnostic Note: - | ||||
| ACTIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the VSV for Swirl Control Valve | Activate the VSV for swirl control valve | ON/OFF | - |
| Control the A/C Cut Signal | Control the A/C signal | ON/OFF | Confirm that the vehicle is stopped and the engine is idling |
| Connect the TC and TE1 | Turn on the TC and TE1 connection | ON/OFF | - |
| Activate the VSV for EGR Cut | Activate vacuum switching valve (for EGR Cut) | ON/OFF | Confirm that the vehicle is stopped and the engine is idling |
| Control the EGR Step Position | Control the electric EGR control valve assembly | 0 to 100% | Test is possible when the following conditions are met:
|
| Test the Turbo Charger Step Motor | Activate the turbocharger | 40 to 100% | Test is possible when the following conditions are met:
|
| Test the Fuel Leak | Pressurize the common rail interior and check for fuel leaks | Stop/Start |
|
| Activate the VN Turbo Open | Activate the turbocharger | ON/OFF | Confirm that the engine is running. |
| Activate the EGR Valve Close | Activate electric vacuum regulating valve assembly | ON/OFF | Confirm that the vehicle is stopped and the engine is idling |
| Control the Cylinder#1 Fuel Cut | Stop fuel injection from the No. 1 injector assembly | ON/OFF | Fuel injection is stopped while the test is ON.
|
| Control the Cylinder#2 Fuel Cut | Stop fuel injection from the No. 2 injector assembly | ON/OFF | Fuel injection is stopped while the test is ON.
|
| Control the Cylinder#3 Fuel Cut | Stop fuel injection from the No. 3 injector assembly | ON/OFF | Fuel injection is stopped while the test is ON.
|
| Control the Cylinder#4 Fuel Cut | Stop fuel injection from the No. 4 injector assembly | ON/OFF | Fuel injection is stopped while the test is ON.
|
| Check the Cylinder Compression* | Check the cylinder compression pressure | ON/OFF | Fuel injection stops in all cylinders. |
| SYSTEM CHECK |
Activate the Pressure Discharge Valve Check
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
![]() |
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Pressure Discharge Valve Check.
![]() |
Press "Next".
![]() |
Press "Next" again to proceed.
![]() |
Select the "Pressure Discharge Valve Check" type.
Press "Next".
Perform troubleshooting based on the measurement results.

