Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Variable Resistor Circuit

for Preparation Click here


DESCRIPTION

This resistor is used to change the air-fuel ratio of the air-fuel mixture.
The idle mixture is adjusted using this resistor.
Turning the idle mixture adjusting screw in the direction of the "R" on the variable resister moves the contacts inside the resistor, raising the terminal VAF voltage. Conversely, turning the screw in the direction of the "L" on the variable resister lowers the terminal VAF voltage.
When the terminal VAF voltage rises, the ECM increases the injection volume slightly, making the air-fuel mixture a little richer.

WIRING DIAGRAM


A121674E02


INSPECTION PROCEDURE

1.CHECK CO/HC
A138030E01
  1. Warm up the engine to normal operating temperature.

  1. Turn all accessories OFF.

  1. Connect all vacuum lines properly.

  1. Connect the tachometer.

  1. Check ignition timing correctly.

  1. Check idle speed correctly.

  1. Check that the CO meter is properly calibrated.

  1. Race the engine at 2,500 rpm for about 2 minutes.

  1. Insert a tester probe at least 40 cm (1.3 ft.) into the tailpipe.

  1. Measure the concentration within 1 to 3 minutes after racing the engine to allow the concentration to stabilize.

    Idle CO concentration:
    0.5 to 2.5%



OK
CHECK FOR PROBLEM SYMPTOMS TABLE
NG


2.ADJUST CO CONCENTRATION
A073579E01
  1. Put the vehicle in the same condition as the previous step (CHECK CO/HC).

  1. Using SST, adjust the idle mixture by turning the idle mixture adjusting screw in the variable resistor.

SST
09243-00020  
Result 
Result
Proceed
Concentration: 1.5 +-1%
B
Change in CO concentration
C
No change in CO concentration
A

HINT:
  1. Always check idle speed after turning the idle mixture adjusting screw. If it is incorrect, readjust idle speed.
  2. The idle mixture adjusting screw can be turned within 180°. Do not turn this screw more than specified.



B
ADJUSTMENT COMPLETE

C
CHECK CO/HC
A


3.INSPECT VARIABLE RESISTOR
A074545E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    3.5 to 6.5 Ω

  1. While fully turning the idle mixture adjusting screw clockwise and counterclockwise using SST, measure the resistance.

SST
09243-00020  

Standard resistance:
Tester Connection
Specified Condition
2 - 3
Resistance changes from approximately 5 to 0 kΩ



NG
REPLACE VARIABLE RESISTOR
OK


4.CHECK ECM (VAF VOLTAGE)
G038493E04
  1. Turn the ignition switch ON.

  1. While fully turning the idle mixture adjusting screw clockwise and counterclockwise slowly using SST, measure the voltage.

SST
09243-00020  

Standard voltage:
Tester Connection
Specified Condition
E11-25 (VAF) - E11-28 (E2)
Voltage changes smoothly from 0 to approximately 5 V (does not change suddenly)



OK
REPLACE ECM
NG


5.CHECK HARNESS AND CONNECTOR (VARIABLE RESISTOR - ECM)
A113859E03
  1. Disconnect the V6 variable resistor connector.

  1. Disconnect the E11 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    V6-2 (VC) - E11-18 (VC)
    Below 1 Ω
    V6-3 (VAF) - E11-25 (VAF)
    Below 1 Ω
    V6-1 (E2) - E11-28 (E2)
    Below 1 Ω
    V6-2 (VC) or E11-18 (VC) - Body ground
    10 kΩ or higher
    V6-3 (VAF) or E11-25 (VAF) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM