Home › TRANSMISSION ยท A343F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION UNIT

AUTOMATIC TRANSMISSION UNIT > INSPECTION

for Preparation Click here



1. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
  1. Remove the magnets and use them to collect steel particles.

  1. Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

    1. Steel (magnetic): bearing, gear and clutch plate wear.
    2. Brass (non-magnetic): bush wear.



2. INSPECT OVERDRIVE 1-WAY CLUTCH


AT08138E04
  1. Hold the overdrive direct clutch drum and turn the input shaft. Check that the input shaft can be turned clockwise freely and locks when turned counterclockwise.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free



3. INSPECT OVERDRIVE DIRECT CLUTCH DISC


C212466
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes.



4. INSPECT OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY


C212467
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    15.8 mm (0.622 in.)

    If the length is not as specified, replace the overdrive clutch return spring sub-assembly.



5. INSPECT OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY


AT08150E01
  1. Check that the check ball is free by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.
    If the result is not as specified, replace the overdrive direct clutch piston sub-assembly.



6. INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY


C213737
  1. Using a dial indicator, measure the inside diameter of the clutch drum bushes.

    Standard inside diameter:
    27.037 to 27.063 mm (1.0645 to 1.0654 in.)

    If the inside diameter is not as specified, replace the overdrive direct clutch drum sub-assembly.



7. INSPECT OVERDRIVE PLANETARY GEAR ASSEMBLY


AT08143E01
  1. Using a dial indicator, measure the inside diameter of the planetary gear bush.

    Standard inside diameter:
    11.200 to 11.221 mm (0.4409 to 0.4417 in.)

    If the inside diameter is not as specified, replace the overdrive planetary gear assembly.



    AT04450E01
  1. Using a feeler gauge, measure the planetary pinion gear thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00788 to 0.0236 in.)

    If the clearance is not as specified, replace the overdrive planetary gear assembly.



8. INSPECT OVERDRIVE BRAKE DISC


C212469
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes.



9. INSPECT PISTON OPERATION OF OVERDRIVE BRAKE


AT08451E01
  1. Place the overdrive support assembly onto the direct clutch assembly.



    AT08149E01
  1. Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) into the oil passage and check that the overdrive brake piston moves smoothly.



10. INSPECT OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


C212468
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.03 mm (0.671 in.)

    If the length is not as specified, replace the overdrive brake return spring sub-assembly.



11. INSPECT DIRECT CLUTCH DISC


C212470
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes.



12. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


C212471
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    21.32 mm (0.839 in.)

    If the length is not as specified, replace the direct clutch return spring sub-assembly.



13. INSPECT DIRECT CLUTCH PISTON SUB-ASSEMBLY


D001424E01
  1. Check that the check ball is free by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.



14. INSPECT DIRECT CLUTCH DRUM SUB-ASSEMBLY


D001352E01
  1. Using a dial indicator, measure the inside diameter of the clutch drum bush.

    Standard inside diameter:
    53.915 to 53.94 mm (2.1227 to 2.1236 in.)

    If the inside diameter is not as specified, replace the direct clutch drum sub-assembly.



15. INSPECT FORWARD CLUTCH DISC


C212473
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes.



16. INSPECT FORWARD CLUTCH PISTON SUB-ASSEMBLY


D001424E01
  1. Check that the check ball is free by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.



17. INSPECT INPUT SHAFT SUB-ASSEMBLY


AT08171E01
  1. Using a dial indicator, measure the inside diameter of the input shaft bush.

    Standard inside diameter:
    24.000 to 24.026 mm (0.9449 to 0.9459 in.)

    If the inside diameter is not as specified, replace the input shaft sub-assembly.



18. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


C212474
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    19.47 mm (0.767 in.)

    If the length is not as specified, replace the forward clutch return spring sub-assembly.



19. INSPECT SECOND COAST BRAKE PISTON ROD


AT07705E01
  1. Check the piston rod length.

    HINT:
    There are 2 different standard lengths for the piston rod.

    Piston Rod Length:
    Groove Mark
    Length
    Without
    78.3 to 78.5 mm (3.083 to 3.090 in.)
    With
    79.8 to 80.0 mm (3.142 to 3.149 in.)

    If the length is not as specified, replace the rod with a new one even if the brake band works normally.



20. INSPECT SECOND COAST BRAKE BAND ASSEMBLY


D025701E04
Text in Illustration 
*1
Printed Number

NOTICE:
  1. If the lining of the brake band is peeled off or discolored, or if any part of the printed numbers is damaged, replace the brake band.
  2. When installing a new band, soak it in ATF for at least 15 minutes before installation.



21. INSPECT FRONT PLANETARY RING GEAR SUB-ASSEMBLY


AT08187E01
  1. Using a dial indicator, measure the inside diameter of the planetary ring gear bush.

    Standard inside diameter:
    24.000 to 24.026 mm (0.9449 to 0.9459 in.)

    If the inside diameter is not as specified, replace the front planetary ring gear sub-assembly.



22. INSPECT FRONT PLANETARY GEAR ASSEMBLY


D029743E01
  1. Using a feeler gauge, measure the pinion gear thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00788 to 0.0236 in.)

    If the clearance is not as specified, replace the front planetary gear assembly.



23. INSPECT NO. 1 1-WAY CLUTCH ASSEMBLY


AT08440E03
  1. Hold the planetary sun gear and turn the 1-way clutch assembly. Check that the 1-way clutch hub can be turned clockwise freely and locks when turned counterclockwise.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free



24. INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY


AT08337E01
  1. Using a dial indicator, measure the inside diameter of the planetary sun gear bushes.

    Standard inside diameter:
    27.000 to 27.026 mm (1.0630 to 1.0640 in.)

    If the inside diameter is not as specified, replace the planetary sun gear sub-assembly.



25. INSPECT SECOND BRAKE PISTON


AT08439E01
  1. Check that the second brake piston moves smoothly when applying compressed air to and releasing low-pressure compressed air from the second brake drum.



26. INSPECT SECOND BRAKE DISC


C212478
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes.



27. INSPECT SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


C212479
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    16.05 mm (0.632 in.)

    If the length is not as specified, replace the second brake piston return spring sub-assembly.



28. INSPECT FIRST AND REVERSE BRAKE DISC


C212463
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes.



29. INSPECT NO. 2 1-WAY CLUTCH


AT08200E04
  1. Hold the planetary gear and turn the 1-way clutch inner race. Check that the 1-way clutch inner race can be turned counterclockwise freely and locks when turned clockwise.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free



30. INSPECT REAR PLANETARY GEAR ASSEMBLY


AT04459E01
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00788 to 0.0236 in.)

    If the clearance is not as specified, replace the rear planetary gear assembly.



31. INSPECT FIRST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


C212464
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    12.902 mm (0.508 in.)

    If the length is not as specified, replace the first and reverse brake return spring sub-assembly.



32. INSPECT TRANSMISSION CASE BUSH


AT08224E01
  1. Using a cylinder gauge, measure the inside diameter of the transmission case rear bush.

    Standard inside diameter:
    38.113 to 38.138 mm (1.50051 to 1.50149 in.)

    If the inside diameter is not as specified, replace the automatic transmission case sub-assembly.



33. INSPECT PISTON OPERATION OF FIRST AND REVERSE BRAKE


AT05258E02
  1. Make sure the first and reverse brake pistons move smoothly when compressed air is applied into the transmission case.



34. INSPECT PISTON OPERATION OF SECOND COAST BRAKE


AT05216E04
  1. Place a mark on the second coast brake piston rod.
    Text in Illustration 
    *1
    Mark
    *2
    Piston Rod



    AT05217E02
  1. Using SST, measure the stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).

    SST
    09240-00020  

    Standard piston stroke:
    1.5 to 3.0 mm (0.0591 to 0.118 in.)

    If the stroke is not as specified, replace the brake band with a new one.



35. INSPECT OUTPUT SHAFT END PLAY


C241556
  1. Using a dial indicator, measure the end play of the output shaft while moving it by hand.

    Standard end play:
    0.30 to 1.04 mm (0.0119 to 0.0409 in.)

    If the end play is not as specified, check for improper installation.

  1. Check that the output shaft rotates smoothly.