Home › TRANSMISSION ยท A343F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION UNIT

AUTOMATIC TRANSMISSION UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE DRAIN PLUG
  1. Remove the drain plug and gasket.



2. REMOVE BREATHER HOSE


C220536E01
  1. Remove the bolt and breather hose.



3. REMOVE TRANSMISSION CONTROL SHAFT LEVER LH


D028070E02
  1. Remove the nut, washer and control shaft lever.



4. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


C241044
  1. Using a screwdriver, bend the tabs of the lock washer.

  1. Remove the nut and lock washer.

  1. Remove the bolt and park/neutral position switch.

    HINT:
    Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.



5. REMOVE ATF TEMPERATURE SENSOR


C239915
  1. Detach the sensor connector clamp from the wire harness bracket.

  1. Using a 19 mm union nut wrench, remove the sensor from the transmission assembly.

  1. Remove the bolt and wire harness bracket.

  1. Remove the O-ring from the sensor.



6. REMOVE OIL COOLER TUBE UNION


G034863E01
  1. Remove the 2 tube unions.

  1. Remove the 2 O-rings from each tube union.



7. REMOVE SPEED SENSOR NC0


Q003894E01
  1. Remove the bolt and sensor.

  1. Remove the O-ring from the sensor.



8. REMOVE SPEED SENSOR SP2


G035550E01
  1. Remove the bolt and sensor.

  1. Remove the O-ring from the sensor.



9. REMOVE AUTOMATIC TRANSMISSION HOUSING


C220031
  1. Remove the 6 bolts.

  1. Remove the transmission housing.



10. SECURE TRANSMISSION CASE


AT05092E01
  1. Secure the transmission case to an overhaul attachment.



11. REMOVE REAR TRANSFER ADAPTER


D028071E01
  1. Remove the 8 bolts.

  1. Remove the rear transfer adapter.



12. REMOVE REAR TRANSFER CASE ADAPTER OIL SEAL


    D027909E02
  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Do not damage the rear transfer adapter.

    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



13. REMOVE REAR TRANSFER CASE ADAPTER OIL RECEIVER


C212453
  1. Using snap ring expander, remove the snap ring.

  1. Remove the rear transfer case adaptor oil receiver from the rear transfer adaptor.



14. REMOVE SENSOR ROTOR


    AT05751E01
  1. Using snap ring expander, remove the snap ring.



    C212455
  1. Remove the sensor rotor and key.



15. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


C238060

NOTICE:
Do not turn the transmission over as this will contaminate the valve body with foreign matter located at the bottom of the oil pan.

  1. Remove the 19 bolts.



    Q007487E04
  1. Insert the blade of an oil pan seal cutter between the transmission case and oil pan, and then cut through the applied sealer.

    NOTICE:
    Be careful not to damage the flanges of the oil pan and transmission case.

  1. Remove the pan from the transmission case.



16. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
  1. Remove the magnets and use them to collect steel particles.

  1. Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

    1. Steel (magnetic): bearing, gear and clutch plate wear.
    2. Brass (non-magnetic): bush wear.



17. REMOVE VALVE BODY OIL STRAINER ASSEMBLY
  1. Turn over the transmission.



    D028706E02
  1. Remove the 4 bolts and valve body oil strainer from the valve body.

  1. Remove the 3 gaskets from the oil strainer.



18. REMOVE TRANSMISSION WIRE


C238020
  1. Disconnect the 4 connectors from the shift solenoid valves.



    G036410E01
  1. Remove the bolt and stopper plate from the case.

  1. Pull out the transmission wire from the transmission case to remove it.

  1. Remove the O-ring from the transmission wire connector.



19. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


D029011E01
  1. Remove the 20 bolts and valve body.



20. REMOVE CHECK BALL BODY


AT04847E02
  1. Remove the check ball body and spring.
    Text in Illustration 
    *1
    Check Ball Body
    *2
    Spring



21. REMOVE B-2 ACCUMULATOR PISTON


D006514E01
  1. Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole to remove the B-2 accumulator piston and spring.

    NOTICE:
    1. The application of compressed air may cause the piston to jump out. When removing the piston, hold it using a piece of cloth.
    2. Take care not to splash ATF when applying the compressed air.

  1. Remove the 2 O-rings from the piston.



22. REMOVE C-2 ACCUMULATOR PISTON


D006514E02
  1. Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole to remove the C-2 accumulator piston and 2 springs.

    NOTICE:
    1. The application of compressed air may cause the piston to jump out. When removing the piston, hold it using a piece of cloth.
    2. Take care not to splash ATF when applying the compressed air.

  1. Remove the 2 O-rings from the piston.



23. REMOVE B-0 ACCUMULATOR PISTON


D006515E01
  1. Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole to remove the B-0 accumulator piston and spring.

    NOTICE:
    1. The application of compressed air may cause the piston to jump out. When removing the piston, hold it using a piece of cloth.
    2. Take care not to splash ATF when applying the compressed air.

  1. Remove the 2 O-rings from the piston.



24. REMOVE C-0 ACCUMULATOR PISTON


D006516E01
  1. Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole to remove the C-0 accumulator piston and 2 springs.

    NOTICE:
    1. The application of compressed air may cause the piston to jump out. When removing the piston, hold it using a piece of cloth.
    2. Take care not to splash ATF when applying the compressed air.

  1. Remove the O-ring from the piston.



25. REMOVE PARKING LOCK PAWL BRACKET


AT05103E01
  1. Remove the 3 bolts and bracket.



26. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


AT05120E01
  1. Disconnect the parking lock rod from the manual valve lever to remove it.



27. REMOVE PARKING LOCK PAWL


Z006720E04
  1. Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.
    Text in Illustration 
    *1
    Parking Lock Pawl Shaft
    *2
    Lock Pawl
    *3
    Spring
    *4
    E-Ring

  1. Remove the E-ring from the shaft.



28. REMOVE MANUAL VALVE LEVER SHAFT


Z006721E04
  1. Using a hammer and screwdriver, cut off the spacer and remove it from the shaft.
    Text in Illustration 
    *1
    Spacer



    AT05105E01
  1. Using a pin punch and hammer, tap out the spring pin.

    HINT:
    Tap out the spring pin slowly so that it does not fall into the transmission case.

  1. Pull out the manual valve lever shaft through the case and remove the manual valve lever.



29. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    C240211E01
  1. Using a screwdriver, pry out the 2 oil seals.

    NOTICE:
    Be careful not to damage the transmission case.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



30. REMOVE OIL PUMP ASSEMBLY


AT05122E02
  1. Stand the transmission upright.

  1. Remove the 7 bolts from the transmission case.



    AT07874E03
  1. Using SST, remove the oil pump.

    SST
    09610-20012  

  1. Remove the O-ring from the oil pump.



    AT08431E01
  1. Remove the bearing race from the oil pump.



31. REMOVE OVERDRIVE PLANETARY GEAR ASSEMBLY WITH OVERDRIVE DIRECT CLUTCH AND OVERDRIVE 1-WAY CLUTCH ASSEMBLY


C212458
  1. Remove the planetary gear together with the direct clutch and 1-way clutch from the transmission case.



    C212459E01
  1. Remove the bearing race and bearing.
    Text in Illustration 
    *1
    Bearing Race
    *2
    Bearing



32. INSPECT OVERDRIVE 1-WAY CLUTCH


AT08138E04
  1. Hold the overdrive direct clutch drum and turn the input shaft. Check that the input shaft can be turned clockwise freely and locks when turned counterclockwise.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free



33. REMOVE OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY


C213736


34. REMOVE OVERDRIVE DIRECT CLUTCH DISC SET


    C237869E01
  1. Using a screwdriver, pry out the snap ring from the overdrive direct clutch drum.

    NOTICE:
    Be careful not to damage the overdrive direct clutch drum.

    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the flange, 2 discs and 2 plates.



35. INSPECT OVERDRIVE DIRECT CLUTCH DISC


C212466
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes.



36. REMOVE OVERDRIVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


C212482E02
  1. Place SST on the return spring and compress the return spring with a press.

    SST
    09350-30020   (09350-07040)

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. Remove the clutch return spring.



37. INSPECT OVERDRIVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


C212467
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    15.8 mm (0.622 in.)

    If the length is not as specified, replace the overdrive clutch return spring sub-assembly.



38. REMOVE OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY


AT03151E01
  1. Place the oil pump onto the torque converter, and then place the overdrive direct clutch onto the oil pump.

  1. Hold the overdrive direct clutch piston by hand and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil pump to remove the overdrive direct clutch piston.

    HINT:
    If the piston is at an angle and cannot be removed, press down on the protruding side and apply compressed air again.

  1. Remove the 2 O-rings from the piston.



39. INSPECT OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY


AT08150E01
  1. Check that the check ball is free by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.
    If the result is not as specified, replace the overdrive direct clutch piston sub-assembly.



40. INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY


C213737
  1. Using a dial indicator, measure the inside diameter of the clutch drum bushes.

    Standard inside diameter:
    27.037 to 27.063 mm (1.0645 to 1.0654 in.)

    If the inside diameter is not as specified, replace the overdrive direct clutch drum sub-assembly.



41. REMOVE OVERDRIVE RETAINING PLATE


    C237778E01
  1. Using a screwdriver, pry out the snap ring.

    NOTICE:
    Be careful not to damage the overdrive planetary gear assembly and the plate.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    AT08146E01
  1. Remove the retaining plate.



42. REMOVE OVERDRIVE 1-WAY CLUTCH OUTER RACE WITH OVERDRIVE 1-WAY CLUTCH


AT08147E01


43. REMOVE OVERDRIVE 1-WAY CLUTCH


C212484
  1. Remove the overdrive 1-way clutch from the outer race.



44. REMOVE NO. 3 OVERDRIVE PLANETARY GEAR THRUST WASHER


C212485


45. INSPECT OVERDRIVE PLANETARY GEAR ASSEMBLY


AT08143E01
  1. Using a dial indicator, measure the inside diameter of the planetary gear bush.

    Standard inside diameter:
    11.200 to 11.221 mm (0.4409 to 0.4417 in.)

    If the inside diameter is not as specified, replace the overdrive planetary gear assembly.



    AT04450E01
  1. Using a feeler gauge, measure the planetary pinion gear thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00788 to 0.0236 in.)

    If the clearance is not as specified, replace the overdrive planetary gear assembly.



46. REMOVE OVERDRIVE PLANETARY RING GEAR WITH OVERDRIVE PLANETARY RING GEAR FLANGE


AT05146E01
  1. Remove the ring gear together with the overdrive planetary ring gear flange from the transmission case.



    G035541E05
  1. Remove the bearing and bearing race from the overdrive planetary ring gear.
    Text in Illustration 
    *1
    Bearing
    *2
    Bearing Race



47. REMOVE OVERDRIVE PLANETARY RING GEAR FLANGE


    C237777E01
  1. Using a screwdriver, pry out the snap ring.

    NOTICE:
    Be careful not to damage the overdrive planetary ring gear and the flange.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    AT08134E01
  1. Remove the ring gear flange from the overdrive planetary ring gear.



48. REMOVE OVERDRIVE BRAKE DISC SET


    C237772E01
  1. Using a screwdriver, pry out the snap ring.

    NOTICE:
    Be careful not to damage the transmission case.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the flange, 4 discs and 4 plates from the transmission case.



49. INSPECT OVERDRIVE BRAKE DISC


C212469
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes.



50. INSPECT PISTON STROKE OF SECOND COAST BRAKE


AT05216E04
  1. Using a waterproof pen, place a mark on the second coast brake piston rod as shown in the illustration.
    Text in Illustration 
    *1
    Piston Rod
    *2
    Mark



    AT05217E02
  1. Using SST, measure the piston stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).

    SST
    09240-00020  

    Standard piston stroke:
    1.5 to 3.0 mm (0.0591 to 0.118 in.)

    If the stroke is not as specified, inspect the brake band.



51. REMOVE OVERDRIVE SUPPORT SUB-ASSEMBLY


AT05148E02
  1. Remove the 2 bolts holding the overdrive support sub-assembly to the case.



    AT05249E03
  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07060)



    AT05211E03
  1. Using SST, remove the overdrive brake assembly.

    SST
    09350-30020   (09350-07020)



    AT05110E07
  1. Remove the bearing and bearing race from the overdrive brake.
    Text in Illustration 
    *1
    Bearing
    *2
    Bearing Race



52. REMOVE DIRECT CLUTCH ASSEMBLY WITH FORWARD CLUTCH ASSEMBLY


AT05149E01
  1. Remove the direct clutch together with the forward clutch from the case.



    AT03149E03
  1. Remove the 2 bearings and bearing race.
    Text in Illustration 
    *1
    Bearing
    *2
    Bearing Race



53. REMOVE FORWARD CLUTCH ASSEMBLY


AT05262E03
  1. Remove the forward clutch from the direct clutch.



    C238271E01
  1. Remove the thrust washer from the forward clutch.
    Text in Illustration 
    *1
    Thrust Washer



54. INSPECT PISTON OPERATION OF OVERDRIVE BRAKE


AT08451E01
  1. Place the overdrive support assembly onto the direct clutch assembly.



    AT08149E01
  1. Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) into the oil passage and check that the overdrive brake piston moves smoothly.



55. REMOVE OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    C237868E01
  1. Place SST on the return spring and compress the return spring with a press.
    Text in Illustration 
    *1
    Protective Tape

    SST
    09350-30020   (09350-07030)

  1. Using a screwdriver, pry out the snap ring.

    NOTICE:
    Be careful not to damage the overdrive support sub-assembly and return spring.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the brake return spring.



56. INSPECT OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


C212468
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.03 mm (0.671 in.)

    If the length is not as specified, replace the overdrive brake return spring sub-assembly.



57. REMOVE OVERDRIVE BRAKE PISTON


C212486
  1. Place the overdrive support onto the direct clutch assembly.

  1. Hold the overdrive brake piston so that it is not slanted and apply compressed air (392 kPa (4 kgf/cm2, 57 psi)) into the passage to remove the overdrive brake piston.



    D001336E04
  1. Remove the 2 O-rings from the overdrive brake piston.
    Text in Illustration 
    *1
    O-Ring



58. REMOVE OVERDRIVE CLUTCH DRUM OIL SEAL RING


AT08160E01
  1. Remove the 2 oil seal rings from the overdrive support.



    AT08158E01
  1. Remove the clutch drum thrust washer from the overdrive support.



59. REMOVE SECOND COAST BRAKE PISTON


AT05127E01
  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07060)



    AT05280E01
  1. Apply compressed air to the oil hole to remove the second coast brake cover, piston assembly and spring.

  1. Remove the 2 O-rings from the cover.



60. REMOVE SECOND COAST BRAKE PISTON OIL SEAL RING


AT05418E01


61. REMOVE SECOND COAST BRAKE PISTON ROD


AT05260E01
  1. Firmly press the piston down to compress the compression spring.

  1. Remove the E-ring.



    D001299E05
  1. Remove the piston rod, washer plate and spring from the piston.
    Text in Illustration 
    *1
    Piston Rod
    *2
    Washer Plate
    *3
    Spring
    *4
    Piston



62. REMOVE DIRECT CLUTCH DISC SET


    C237874E01
  1. Using a screwdriver, pry out the snap ring from the direct clutch drum.

    NOTICE:
    Be careful not to damage the direct clutch drum.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the flange, 3 discs and 3 plates.



63. INSPECT DIRECT CLUTCH DISC


C212470
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes.



64. REMOVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


AT08168E02
  1. Place SST on the spring retainer and compress the return spring with a press.

    SST
    09350-30020   (09350-07040)

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. Remove the return spring.



65. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


C212471
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    21.32 mm (0.839 in.)

    If the length is not as specified, replace the direct clutch return spring sub-assembly.



66. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY


G037157E01
  1. Place the direct clutch drum on the overdrive support.

  1. Hold the direct clutch piston and apply compressed air (196 kPa (2.0 kgf/cm2, 28.5 psi)) to the overdrive support to remove the direct clutch piston.

    HINT:
    Make sure the direct clutch piston is not tilted before applying compressed air.



    C237870E01
  1. Using a small screwdriver, remove the 2 O-rings from the piston.
    Text in Illustration 
    *1
    O-Ring
    *2
    Protective Tape

    NOTICE:
    Be careful not to damage the direct clutch piston sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



67. INSPECT DIRECT CLUTCH PISTON SUB-ASSEMBLY


D001424E01
  1. Check that the check ball is free by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.



68. INSPECT DIRECT CLUTCH DRUM SUB-ASSEMBLY


D001352E01
  1. Using a dial indicator, measure the inside diameter of the clutch drum bush.

    Standard inside diameter:
    53.915 to 53.94 mm (2.1227 to 2.1236 in.)

    If the inside diameter is not as specified, replace the direct clutch drum sub-assembly.



69. FIX FORWARD CLUTCH ASSEMBLY


AT08165E01
  1. Place the overdrive support on wooden blocks or equivalent to prevent the forward clutch shaft from touching the work stand.

  1. Place the forward clutch on the overdrive support.



70. REMOVE FORWARD CLUTCH DISC SET


    C237871E01
  1. Using a screwdriver, pry out the snap ring from the input shaft.

    NOTICE:
    Be careful not to damage the input shaft.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the flange, 5 discs and 5 plates.



    AT08177E01
  1. Remove the cushion plate.



71. INSPECT FORWARD CLUTCH DISC


C212473
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes.



72. REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


D001274E03
  1. Place SST on the spring retainer and compress the return spring with a press.

    SST
    09350-30020   (09350-07040)

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)



    D001359E04
  1. Remove the return spring.



73. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


C212474
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    19.47 mm (0.767 in.)

    If the length is not as specified, replace the forward clutch return spring sub-assembly.



74. REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY


D025661E01
  1. Place the input shaft onto the overdrive support.

  1. Hold the forward clutch piston by hand and apply compressed air (196 kPa (2.0 kgf/cm2, 28.5 psi)) to the overdrive support to remove the forward clutch piston.



    C240212E01
  1. Remove the O-ring from the input shaft.

    NOTICE:
    Be careful not to damage the input shaft sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    D001361E04
  1. Remove the 2 O-rings from the forward clutch piston.
    Text in Illustration 
    *1
    O-Ring
    *2
    Protective Tape

    NOTICE:
    Be careful not to damage the damage the forward clutch piston sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



75. INSPECT FORWARD CLUTCH PISTON SUB-ASSEMBLY


D001424E01
  1. Check that the check ball is free by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.



76. REMOVE INPUT SHAFT OIL SEAL RING


AT08180E01
  1. Remove the 3 oil seal rings from the input shaft.



77. INSPECT INPUT SHAFT SUB-ASSEMBLY


AT08171E01
  1. Using a dial indicator, measure the inside diameter of the input shaft bush.

    Standard inside diameter:
    24.000 to 24.026 mm (0.9449 to 0.9459 in.)

    If the inside diameter is not as specified, replace the input shaft sub-assembly.



78. REMOVE SECOND COAST BRAKE BAND ASSEMBLY


    C237773E01
  1. Using a screwdriver, pry off the 2 E-rings from the pin and pull out the pin.

    NOTICE:
    Be careful not to damage the damage the transmission case.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    Q004030E01
  1. Remove the second coast brake band from the case.



79. INSPECT SECOND COAST BRAKE BAND ASSEMBLY


D025701E04
Text in Illustration 
*1
Printed Number

NOTICE:
  1. If the lining of the brake band is peeled off or discolored, or if any part of the printed numbers is damaged, replace the brake band.
  2. When installing a new band, soak it in ATF for at least 15 minutes before installation.



80. REMOVE FRONT PLANETARY RING GEAR SUB-ASSEMBLY


AT05128E01
  1. Remove the planetary ring gear from the case.



    C238270E01
  1. Remove the bearing and bearing race from the planetary ring gear.
    Text in Illustration 
    *1
    Bearing
    *2
    Bearing Race



    C241555E01
  1. Place the output shaft on wooden blocks or equivalent.
    Text in Illustration 
    *1
    Wooden Block



81. INSPECT FRONT PLANETARY RING GEAR SUB-ASSEMBLY


AT08187E01
  1. Using a dial indicator, measure the inside diameter of the planetary ring gear bush.

    Standard inside diameter:
    24.000 to 24.026 mm (0.9449 to 0.9459 in.)

    If the inside diameter is not as specified, replace the front planetary ring gear sub-assembly.



82. REMOVE FRONT PLANETARY GEAR ASSEMBLY


D029744E01
  1. Remove the bearing race from the planetary gear.



    D029740E03
  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)



    D029741E01
  1. Remove the planetary gear from the case.



    C237873E01
  1. Remove the bearing and bearing race from the planetary gear.

    NOTICE:
    Be careful not to damage the damage the front planetary gear assembly.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



83. INSPECT FRONT PLANETARY GEAR ASSEMBLY


D029743E01
  1. Using a feeler gauge, measure the pinion gear thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00788 to 0.0236 in.)

    If the clearance is not as specified, replace the front planetary gear assembly.



84. REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY WITH SUN GEAR INPUT DRUM AND NO. 1 1-WAY CLUTCH ASSEMBLY


C238269
  1. Remove the sun gear together with the sun gear input drum and 1-way clutch from the case.



85. INSPECT NO. 1 1-WAY CLUTCH ASSEMBLY


AT08440E03
  1. Hold the planetary sun gear and turn the 1-way clutch assembly. Check that the 1-way clutch hub can be turned clockwise freely and locks when turned counterclockwise.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free



86. REMOVE NO. 1 1-WAY CLUTCH ASSEMBLY


AT08188E01


87. REMOVE NO. 1 1-WAY CLUTCH THRUST WASHER


AT01642E01


88. REMOVE SUN GEAR SHAFT OIL SEAL RING


AT08189E01
  1. Remove the 2 oil seal rings from the sun gear input drum.



89. REMOVE SUN GEAR INPUT DRUM


AT08190E02
  1. Place the planetary sun gear onto a wooden block or equivalent.

  1. Using snap ring pliers, remove the snap ring.

  1. Remove the input drum from the planetary sun gear.



90. REMOVE SUN GEAR INPUT DRUM SHAFT SNAP RING


    C237780E01
  1. Using a screwdriver, pry off the snap ring from the planetary sun gear.

    NOTICE:
    Be careful not to damage the damage the front planetary sun gear sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



91. INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY


AT08337E01
  1. Using a dial indicator, measure the inside diameter of the planetary sun gear bushes.

    Standard inside diameter:
    27.000 to 27.026 mm (1.0630 to 1.0640 in.)

    If the inside diameter is not as specified, replace the planetary sun gear sub-assembly.



92. REMOVE SECOND BRAKE PISTON SLEEVE


    C237774E01
  1. Using a screwdriver, remove the sleeve.

    NOTICE:
    Be careful not to damage the damage the transmission case.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



93. REMOVE SECOND BRAKE DISC SET


    C237775E01
  1. Using a screwdriver, pry out the snap ring.

    NOTICE:
    Be careful not to damage the damage the transmission case and sleeve.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the flange, 5 discs and 5 plates.



94. REMOVE OUTPUT SHAFT WITH REAR PLANETARY GEAR, NO. 2 1-WAY CLUTCH, FIRST AND REVERSE BRAKE DISC SET AND SECOND BRAKE DRUM


AT05460E03
  1. Using SST and a screwdriver, remove the snap ring.

    SST
    09350-30020   (09350-07060)



    AT05158E01
  1. Remove the output shaft together with the rear planetary gear, No. 2 1-way clutch, first and reverse brake disc set and second brake drum from the transmission case.



    AT05132E01
  1. Remove the bearing from the transmission case.



95. REMOVE SECOND BRAKE DRUM SUB-ASSEMBLY


Q004066E01
  1. Remove the second brake drum.



96. REMOVE NO. 4 PLANETARY CARRIER THRUST WASHER


AT08184E01


97. INSPECT SECOND BRAKE PISTON


AT08439E01
  1. Check that the second brake piston moves smoothly when applying compressed air to and releasing low-pressure compressed air from the second brake drum.



98. REMOVE SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


AT08438E03
  1. Place SST on the spring retainer and compress the piston return spring with a press.

    SST
    09350-30020   (09350-07040)

    NOTICE:
    Do not deform the spring seat. Stop compressing the spring when the spring seat is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove.

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. Remove the second brake piston return spring seat.



    AT08185E03
  1. Remove the piston return spring.



99. INSPECT SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


C212479
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    16.05 mm (0.632 in.)

    If the length is not as specified, replace the second brake piston return spring sub-assembly.



100. REMOVE SECOND BRAKE PISTON


AT08196E01
  1. Hold the second brake piston by hand and apply compressed air to the second brake drum to remove the second brake piston.

    HINT:
    If the piston is at an angle and cannot be removed, press down on the protruding side and apply compressed air again.

  1. Remove the 2 O-rings from the piston.



101. REMOVE FIRST AND REVERSE BRAKE DISC SET
  1. Remove the flange, 6 plates and 6 discs.



102. INSPECT FIRST AND REVERSE BRAKE DISC


C212463
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes.



103. REMOVE OUTPUT SHAFT


AT08197E01


104. REMOVE PLANETARY OUTPUT SHAFT OIL SEAL RING


AT08198E01


105. REMOVE REAR PLANETARY RING GEAR


AT08199E01
  1. Remove the rear planetary gear from the planetary ring gear.



    C212461
  1. Remove the bearing race and bearing from the planetary ring gear.



    C237867E01
  1. Using a screwdriver, pry out the snap ring.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the damage the rear planetary ring gear.

    HINT:
    Tape the screwdriver tip before use.



    AT08207E01
  1. Remove the planetary ring gear flange.



106. INSPECT NO. 2 1-WAY CLUTCH


AT08200E04
  1. Hold the planetary gear and turn the 1-way clutch inner race. Check that the 1-way clutch inner race can be turned counterclockwise freely and locks when turned clockwise.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free



107. REMOVE NO. 2 1-WAY CLUTCH


AT08191E01
  1. Remove the 1-way clutch inner race from the planetary gear.



    C237866E01
  1. Using a screwdriver, pry out the snap ring.
    Text in Illustration 
    *2
    Protective Tape

    NOTICE:
    Be careful not to damage the damage the rear planetary gear.

    HINT:
    Tape the screwdriver tip before use.



    AT08193E01
  1. Remove the 1-way clutch from the rear planetary gear.



    D028060E01
  1. Remove the No. 2 planetary carrier thrust washer from the rear planetary gear.



    D028061E01
  1. Remove the No. 1 planetary carrier thrust washer from the rear planetary gear.



108. INSPECT REAR PLANETARY GEAR ASSEMBLY


AT04459E01
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00788 to 0.0236 in.)

    If the clearance is not as specified, replace the rear planetary gear assembly.



109. REMOVE LEAF SPRING


AT05107E01


110. REMOVE BRAKE DRUM GASKET


AT04444E01


111. REMOVE FIRST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


AT08336E04
  1. Place SST on the first and reverse brake return spring and compress the brake return spring.

    SST
    09350-30020   (09350-07050)
    Text in Illustration 
    *1
    Snap Ring

  1. Using SST, remove the snap ring and brake return spring.

    SST
    09350-30020   (09350-07070)



112. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


C212464
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    12.902 mm (0.508 in.)

    If the length is not as specified, replace the first and reverse brake return spring sub-assembly.



113. REMOVE NO. 2 FIRST AND REVERSE BRAKE PISTON


AT05375E01
  1. Hold the No. 2 first and reverse brake piston and apply compressed air to the transmission case to remove the brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the O-ring from the brake piston.



114. REMOVE BRAKE REACTION SLEEVE


AT08335E01
  1. Using SST, remove the sleeve.

    SST
    09350-30020   (09350-07080)

  1. Remove the O-rings from the sleeve.



115. REMOVE NO. 1 1ST AND REVERSE BRAKE PISTON


AT08334E01
  1. Using SST, remove the brake piston.

    SST
    09350-30020   (09350-07090)

  1. Remove the 2 O-rings from the brake piston.



116. INSPECT TRANSMISSION CASE BUSH


AT08224E01
  1. Using a cylinder gauge, measure the inside diameter of the transmission case rear bush.

    Standard inside diameter:
    38.113 to 38.138 mm (1.50051 to 1.50149 in.)

    If the inside diameter is not as specified, replace the automatic transmission case sub-assembly.