Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › TRANSMISSION CONTROL CABLE

TRANSMISSION CONTROL CABLE > REPLACEMENT

for Preparation Click here



1. REMOVE TRANSFER SHIFT LEVER KNOB SUB-ASSEMBLY


B277221
  1. Twist the shift lever knob in the direction indicated by the arrow and remove it.



2. REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY


B278222
  1. Detach the 4 claws and remove the parking brake hole cover.



3. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


  1. for Manual Transmission:



    1. Detach the 12 claws and remove the upper console panel.

      NOTICE:
      Be careful not to damage the instrument panel and console box with the claws of the upper console panel.



      B277219E01


      Text in Illustration 
      *A
      for 2WD
      *B
      for 4WD



  1. for Automatic Transmission:



    1. Detach the 12 claws and remove the upper console panel.

      NOTICE:
      Be careful not to damage the instrument panel and console box with the claws of the upper console panel.



      B277220E01


      Text in Illustration 
      *A
      for 2WD
      *B
      for 4WD



4. REMOVE CONSOLE BOX ASSEMBLY


B278048E01
  1. Remove the 4 screws and 2 bolts.

  1. Using a clip remover, remove the 2 clips and console box.
    Text in Illustration 
    *1
    Screw
    *2
    Bolt
    *3
    Clip



5. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY


G034281E01
  1. Move the shift lever to L.

  1. Disconnect the control cable from the shift lever.

  1. Remove the lock clip and disconnect the control cable from the bracket.



    G034282E01
  1. Remove the 2 nuts and disconnect the control cable from the vehicle body.



    G034514E01
  1. Remove the nut and disconnect the control cable from the vehicle body.



    G034515E01
  1. Remove the lock clip and control cable bracket.

  1. Remove the nut and control cable.



6. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Install the control cable with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Install the control cable bracket and lock clip.



    G034514E01
  1. Connect the control cable to the body with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    G034282E01
  1. Connect the control cable to the body with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    G034281E01
  1. Connect the control cable to the bracket with the lock clip.

  1. Move the shift lever to L.

  1. Install the control cable to the shift lever.



7. ADJUST SHIFT LEVER POSITION


G034515E01
  1. Remove the nut and disconnect the control cable.

  1. Remove the clip and disconnect the control cable from the control cable bracket.



    D028682E01
  1. Push the control shaft rearward as much as possible.

  1. Return the control shaft lever 2 notches to the N position.

  1. While holding the control shaft lever slightly toward the R position side, tighten the nut.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }



8. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves rearward after shifting to the R.
    If the results are not as specified, inspect the park/neutral position switch and check the shift lever.



9. INSTALL CONSOLE BOX ASSEMBLY


B278048E01
  1. Install the console box with the 4 screws and 2 bolts.

  1. Install the 2 clips.
    Text in Illustration 
    *1
    Screw
    *2
    Bolt
    *3
    Clip



10. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


  1. for Manual Transmission:



    1. Attach the 12 claws to install the upper console panel.


      B277219E01


      Text in Illustration 
      *A
      for 2WD
      *B
      for 4WD



  1. for Automatic Transmission:
    Attach the 12 claws to install the upper console panel.


    B277220E01


    Text in Illustration 
    *A
    for 2WD
    *B
    for 4WD



11. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY
  1. Attach the 4 claws to install the parking brake hole cover.



12. INSTALL TRANSFER SHIFT LEVER KNOB SUB-ASSEMBLY


B277222
  1. Install the shift lever knob and twist it in the direction indicated by the arrow.