WINDSHIELD GLASS > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE INNER REAR VIEW MIRROR ASSEMBLY |
![]() |
w/o Screw:
Push the cover in the direction indicated by the arrows labeled A and remove it.
While holding down the claw in the direction of the black arrow labeled B, slide the inner rear view mirror assembly in the direction of the white arrow and remove it.
| *1 | Cover |
| *2 | Claw |
![]() |
w/ Screw:
Using a T20 "TORX" socket wrench, remove the screw.
Slide the inner rear view mirror assembly in the direction of the arrow and remove it.
| 3. REMOVE FRONT DOOR OPENING TRIM LH |
Partially remove the front door opening trim weatherstrip LH so that the front pillar garnish LH can be removed .
| 4. REMOVE FRONT DOOR OPENING TRIM RH |
| 5. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY |
![]() |
Remove the 2 screws and front assist grip.
| 6. REMOVE FRONT PILLAR GARNISH LH |
![]() |
Detach the 2 clips and 2 guides and remove the front pillar garnish.
![]() |
w/ Curtain Shield Airbag:
Protect the curtain shield airbag assembly.
Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.
| *1 | Protective Cover |
| *2 | Adhesive Tape |
| 7. REMOVE FRONT PILLAR GARNISH RH |
| 8. REMOVE MAP LIGHT ASSEMBLY |
![]() |
Remove the 2 screws.
Detach the claw and 2 guides and remove the map light assembly.
Disconnect the connector.
| 9. REMOVE NO. 1 ROOM LIGHT ASSEMBLY |
![]() |
Using a screwdriver wrapped with protective tape, detach the 4 claws and remove the lens.
![]() |
Remove the 2 screws and room light.
Disconnect the light connector.
| 10. REMOVE VISOR ASSEMBLY LH |
![]() |
Detach the guide.
Remove the 2 screws and visor.
| 11. REMOVE VISOR ASSEMBLY RH |
| 12. REMOVE VISOR HOLDER LH |
![]() |
Remove the screw.
Detach the 2 claws and remove the visor holder.
| 13. REMOVE VISOR HOLDER RH |
| 14. REMOVE ASSIST GRIP |
![]() |
Using a screwdriver, detach the 4 claws and open the 2 covers.
| *1 | Protective Tape |
![]() |
Remove the 2 screws and assist grip.
| 15. REMOVE ROOF HEADLINING ASSEMBLY |
Partially remove the roof headlining .
| 16. REMOVE FRONT WIPER ARM HEAD CAP |
![]() |
Using a screwdriver, remove the front wiper arm head cap.
| 17. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Remove the nut and the front wiper arm and blade assembly LH.
| 18. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Remove the nut and the front wiper arm and blade assembly RH.
| 19. REMOVE HOOD TO COWL TOP SEAL |
![]() |
Using a clip remover, detach the 9 clips and remove the hood to cowl top seal.
| 20. REMOVE COWL TOP VENTILATOR LOUVER LH |
![]() |
Remove the clip.
Detach the 5 claws and 5 guides, and remove the cowl top ventilator louver LH in the direction indicated by the arrow in the illustration.
| 21. REMOVE COWL TOP VENTILATOR LOUVER RH |
![]() |
Remove the clip.
Detach the 5 guides, and remove the cowl top ventilator louver RH in the direction indicated by the arrow in the illustration.
| 22. REMOVE OUTER UPPER WINDSHIELD MOULDING |
![]() |
Using a knife, cut off the moulding as shown in the illustration.
Remove the remaining moulding.
| 23. REMOVE WINDSHIELD GLASS |
![]() |
Apply protective tape to the outer surface of the vehicle body to prevent scratches.
From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
![]() |
Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.
Cut through the adhesive by pulling the piano wire around the glass.
Remove the stoppers.
Using suction cups, remove the glass.
| 24. CLEAN WINDSHIELD GLASS |
![]() |
Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.
Clean the outer edges of the glass with non-residue solvent.
| 25. CLEAN VEHICLE BODY |
![]() |
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
Clean the contact surface of the vehicle body with cleaner.