Home › TRANSMISSION · A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV)

DTC    P2716/77    Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

for Preparation Click here


DESCRIPTION

The throttle pressure that is applied to the primary regulator valve (which modulates the line pressure) causes the solenoid valve SLT, under electronic control, to precisely modulate and generate the line pressure according to the extent that the accelerator pedal is depressed or the output of engine power.
This controls the line pressure and provides smooth shifting characteristics.
Upon receiving a signal of the throttle valve opening angle, the TCM controls the line pressure by sending a predetermined duty ratio* to the solenoid valve, modulating the line pressure and generating throttle pressure.

HINT:
C170551E02
*: The duty ratio is the ratio of the current on time (A) to the total of the current on and off time (A + B).
Duty Ratio (%) = A / (A + B) x 100


DTC Code
DTC Detection Condition
Trouble Area
P2716/77
TCM detects shift solenoid valve SLT circuit malfunction for 1 sec. or more (1 trip detection logic)
  1. Open or short in shift solenoid valve SLT circuit
  2. Shift solenoid valve SLT
  3. TCM

WIRING DIAGRAM


C161203E47


INSPECTION PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)


    C192930E04
  1. Disconnect the E1 wire connector.

  1. Measure the resistance of the transmission wire.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (SLT+) - 6 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    2 (SLT+) - Body ground
    Always
    10 kΩ or higher
    6 (SLT-) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 3
OK


2.CHECK WIRE HARNESS (SHIFT SOLENOID VALVE SLT - TCM)


    C191544E06
  1. Disconnect the T19 TCM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T19-20 (SLT+) - T19-19 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    T19-20 (SLT+) - Body ground
    Always
    10 kΩ or higher
    T19-19 (SLT-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM 

3.INSPECT SHIFT SOLENOID VALVE SLT
C162477E17
  1. Remove the shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω



  1. Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.


    HINT:
    C191543E07
    C170573E01
    Reference: Inspection using an oscilloscope.
    Check the waveform of the TCM connector.

    OK:
    Refer to illustration
    Item
    Content
    Tester Connection
    T19-20 (SLT+) - T19-19 (SLT-)
    Tool Setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Engine is idling



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK

REPLACE TRANSMISSION WIRE