Home › ENGINE · 2KD-FTV › STARTING › STARTER (for 2.7 kW Type)

STARTER (for 2.7 kW Type) > INSPECTION

for Preparation Click here



1. INSPECT STARTER ASSEMBLY


CAUTION:
These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.



A117199E02


Text in Illustration 
*1
Terminal C
*2
Terminal 30
*3
Terminal 50
-
-


  1. Perform pull-in test.

    1. Remove the nut, and then disconnect the field coil lead wire from terminal C.



    2. Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear moves outward.
      If the clutch pinion gear does not move, replace the magnet starter switch assembly.


      A121980E02


      Text in Illustration 
      *a
      Operation
      -
      -



  1. Perform holding test.



    1. When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.
      If the clutch pinion gear moves inward, replace the magnet starter switch assembly.


      A121981E02


      Text in Illustration 
      *1
      Terminal C
      -
      -
      *a
      Disconnect
      -
      -



  1. Inspect clutch pinion gear return.



    1. Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
      If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.


      A121982E02


      Text in Illustration 
      *a
      Operation
      *b
      Disconnect



  1. Perform operation test without load.



      A197157
    1. Connect the field coil lead wire to terminal C with the nut.

      Torque:
      24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    2. Mount the starter in a vise between aluminum plates.



    3. Connect the battery and an ammeter to the starter as shown in the illustration.


      A194373E02


      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal 30
      *a
      Connect
      -
      -

    4. Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.

      Standard current:
      180 A or less at 11 V

      If the result is not as specified, replace the starter assembly.



2. INSPECT STARTER ARMATURE ASSEMBLY


  1. Measure the resistance.



      A115023E06
    1. Measure the resistance between any 2 segments of the commutator.

      Standard resistance:
      Below 1 Ω

      Text in Illustration 
      *1
      Segment
      If the result is not as specified, replace the starter armature assembly.



    2. A115024E06
    3. Measure the resistance between each segment of the commutator and the armature coil core.

      Standard resistance:
      10 kΩ or higher

      Text in Illustration 
      *1
      Segment
      *2
      Armature Coil Core
      If the result is not as specified, replace the starter armature assembly.



    A115025
  1. Inspect circle runout.

    1. Place the armature on V-blocks.

    2. Using a dial gauge, measure the circle runout.

      Maximum circle runout:
      0.05 mm (0.00197 in.)

      If the circle runout is more than the maximum, replace the starter armature assembly.



    A115026
  1. Using a vernier caliper, measure the commutator diameter.

    Standard diameter:
    36.0 mm (1.42 in.)

    Minimum diameter:
    35.0 mm (1.38 in.)

    If the diameter is less than the minimum, replace the starter armature assembly.



    A115027
  1. Measure the undercut depth of the commutator.

    Standard undercut depth:
    0.7 mm (0.0276 in.)

    Minimum undercut depth:
    0.2 mm (0.00787 in.)

    If the under cut depth is less than the minimum, correct it with a hacksaw blade.

  1. Inspect the armature bearings.

    1. Check that the armature bearings rotate smoothly.
      If the result is not as specified, replace the starter armature assembly.



3. INSPECT STARTER YOKE ASSEMBLY


    A197148
  1. Inspect the field coil for an open circuit.

    1. Measure the resistance between the lead wire and field coil brush lead.

      Standard resistance:
      Below 1 Ω

      If the result is not as specified, replace the starter yoke assembly.



    A197149
  1. Inspect the ground.

    1. Measure the resistance between the lead wire and starter yoke body, and between the brushes and starter yoke body

      Standard resistance:
      10 kΩ or higher

      If the result is not as specified, replace the starter yoke assembly.



4. INSPECT BRUSH


    A062430E17
  1. Using a vernier caliper, measure the brush length.
    Text in Illustration 
    *1
    Length
    *a
    Brush Holder Side
    *b
    Starter Yoke Side

    Standard length:
    20.5 mm (0.814 in.)

    Minimum length:
    11.0 mm (0.433 in.)

    If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.



5. INSPECT STARTER BRUSH HOLDER ASSEMBLY


    A115033
  1. Inspect the brush insulation.

    1. Using an ohmmeter, measure the resistance between the positive and negative brush holders.

      Standard resistance:
      10 kΩ or higher

      If the result is not as specified, replace the brush holder assembly.



    A115032
  1. Take the pull scale reading the instant the brush spring separates from the brush.

    Standard spring load:
    26 to 45 N (3 to 5 kgf, 5.8 to 10.1 lbf)

    Minimum spring load:
    12 N (1 kgf, 2.8 lbf)

    If the spring load is less than the minimum, replace the brush spring.



6. INSPECT STARTER CLUTCH SUB-ASSEMBLY


    A115056
  1. Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
    If the result is not as specified, replace the starter clutch sub-assembly.
    Text in Illustration 
    V100135
    Free
    V100136
    Lock



7. INSPECT MAGNET STARTER SWITCH ASSEMBLY


  1. Check if the pull-in coil has an open circuit.



      A197154E02
    1. Measure the resistance between terminal 50 and terminal C.

      Standard resistance:
      Below 1 Ω

      Text in Illustration 
      *1
      Terminal C
      *2
      Terminal 50
      If the result is not as specified, replace the magnet starter switch assembly.



  1. Check if the hold-in coil has an open circuit.



      A197155E02
    1. Measure the resistance between terminal 50 and the switch body.

      Standard resistance:
      Below 2 Ω

      Text in Illustration 
      *1
      Terminal 50
      If the result is not as specified, replace the magnet starter switch assembly.