TURBOCHARGER > INSTALLATION |
| 1. CLEAN TURBOCHARGER SUB-ASSEMBLY |
| 2. INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY |
![]() |
Install a new gasket and No. 1 turbo water pipe with the bolt and 2 nuts.
| *1 | New Gasket |
| 3. INSTALL TURBOCHARGER SUB-ASSEMBLY |
Temporarily install a new gasket and the turbocharger with 3 new nuts.
Temporarily install the turbo oil inlet pipe.
Install a new gasket and the oil inlet pipe with the 2 nuts, but only loosely install the nuts.
Install a new gasket and the turbo oil inlet pipe with the 2 bolts, but only loosely install the bolts.
Install a new gasket and the turbo oil inlet pipe with the union bolt, but only loosely install the union bolt.
Temporarily install the turbocharger stay with the 2 bolts and nut.

| *1 | New Gasket | *2 | Claw |
| *3 | Narrow | *4 | Wide |
![]() | Outside | - | - |
Tighten the 3 nuts of the turbocharger.
Tighten the 2 nuts labeled A.
Tighten the union bolt labeled B.
Tighten the 2 bolts labeled C.
![]() |
Tighten the 2 bolts and nut of the turbocharger stay in the order shown in the illustration.
| 4. INSTALL TURBINE OUTLET ELBOW |
Install a new gasket and the turbine outlet elbow with the 3 new nuts.
| 5. INSTALL NO. 1 TURBO WATER HOSE |
Install the 2 No. 1 turbo water hoses.
| 6. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
Temporarily install the No. 1 exhaust manifold heat insulator with the bolt.
| 7. INSTALL NO. 1 TURBO INSULATOR |
Temporarily install the No. 1 turbo insulator with the 2 bolts.
Tighten the bolt of the No. 1 exhaust manifold heat insulator, and the 2 bolts of the No. 1 turbo insulator.
| 8. INSTALL COMPRESSOR INLET ELBOW |
Install a new gasket and the compressor inlet elbow with the 2 nuts.
Connect the 2 connectors to the turbocharger.
Attach the wire harness clamp.
| 9. INSTALL VENTILATION PIPE |
Connect the 2 ventilation hoses to the cylinder head cover and compressor inlet elbow.
Install the ventilation pipe to the cylinder head with the bolt.
| 10. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the compression spring.
Install the front exhaust pipe to the exhaust pipe support.
![]() |
Install a new gasket to the turbine outlet elbow.
| *1 | Gasket |
| *2 | Turbine Outlet Elbow |
Install the front exhaust pipe and 2 compression springs with the 2 bolts. Alternately tighten the bolts in several passes.
| 11. INSTALL FRONT FENDER SEAL |
Install the front fender seal with the 5 clips.
| 12. INSTALL FRONT FENDER APRON SEAL UPPER |
Install the front fender apron seal upper with the 5 clips.
| 13. INSTALL INTERCOOLER ASSEMBLY |
| 14. INSTALL AIR CLEANER ASSEMBLY |
Connect the air cleaner hose.
Install the cleaner with the 2 bolts.
Tighten the hose clamp.
Connect the connector to the mass air flow meter connector.
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 16. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the B line of the radiator reservoir.
| Item | Specified Condition |
| for Automatic Transmission | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
| for Manual Transmission | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 17. INSPECT FOR COOLANT LEAK |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 18. INSPECT FOR OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
| 19. INSPECT ENGINE OIL LEVEL |
Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
If low, check for leakage and add oil up to the full level mark.
| 20. INSTALL NO. 2 ENGINE UNDER COVER |
| 21. INSTALL NO. 1 ENGINE UNDER COVER |