ENGINE OIL COOLER > INSTALLATION |
| 1. INSTALL OIL COOLER ASSEMBLY |
Install 2 new gaskets and the oil cooler to the filter bracket with the 4 nuts.
| 2. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY |
![]() |
Install a new gasket and oil filter bracket with the 10 bolts and 2 nuts.
| 3. INSTALL OIL FILTER SUB-ASSEMBLY |
Check and clean the oil filter installation surface.
![]() |
Apply clean engine oil to the gasket of a new oil filter.
Install the oil filter, and tighten it by hand until the gasket contacts the installation surface.
Using SST, tighten the oil filter by an additional 3/4 turn to seat the filter.
| 4. INSTALL EXHAUST MANIFOLD |
![]() |
Install a new gasket to the cylinder head.
![]() |
Install the exhaust manifold with the 6 bolts and 2 new nuts. Uniformly tighten the bolts and nuts in several steps.
| 5. INSTALL FRONT EXHAUST PIPE |
Install the front exhaust pipe .
| 6. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the heat insulator with the 3 bolts.
| 7. INSTALL GENERATOR WITH VACUUM PUMP ASSEMBLY |
![]() |
Install the generator with the bolt.
Connect the vacuum oil outlet hose.
![]() |
Install 2 new gaskets and the vacuum pump hose with the union bolt.
Install the vacuum pump oil inlet hose with 2 new gaskets and the union bolt.
Attach the vacuum pump oil inlet hose to the cord clip.
![]() |
Install the generator wire with the nut.
Attach the terminal cap.
Connect the generator connector.
| 8. INSTALL VACUUM PUMP OIL INLET HOSE |
![]() |
Connect the vacuum pump oil inlet hose with 2 new gaskets and the union bolt.
| 9. INSTALL COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System) |
Temporarily install the compressor mounting bracket with the 4 bolts.
![]() |
Using several steps, uniformly install and tighten the 4 bolts.
![]() |
Temporarily install the spacer with the bolt.
| 10. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) |
![]() |
Install the compressor with the 4 bolts.
| 11. INSTALL FAN & GENERATOR V BELT (w/ Air Conditioning System) |
![]() |
Install the V belt.
Tightening bolt C, adjust the deflection of the V belt .
Tighten the bolts A and B.
Recheck the deflection of the V belt.
| 12. INSTALL FAN & GENERATOR V BELT (w/o Air Conditioning System) |
![]() |
Install the V belt.
Using a bar, adjust the tension of the V belt.
Tighten the bolts A and B.
Check the deflection of the V belt .
| 13. INSTALL COOLER COMPRESSOR V BELT (w/ Air Conditioning System) |
![]() |
Install the V belt.
Tightening bolt B, adjust the deflection of the V belt .
Tighten nut A.
Recheck the deflection of the V belt.
| 14. INSTALL VANE PUMP V BELT |
![]() |
Install the V belt.
Using a bar, adjust the deflection of the V belt .
Tighten bolt A and nut B.
Recheck the deflection of the V belt.
| 15. INSTALL INTAKE PIPE |
![]() |
Install the intake pipe with the 2 bolts.
Tighten the intake pipe clamp.
| 16. INSTALL AIR CLEANER ASSEMBLY |
Install the cleaner with the 2 bolts.
Connect the connector to the IAT sensor.
Connect the hose clamp.
| 17. ADD ENGINE OIL |
Add fresh engine oil.
| Item | Specified Condition |
| Drain and refill with oil filter change | 7.2 liters (7.6 US qts, 6.3 Imp. qts) |
| Drain and refill without oil filter change | 6.7 liters (7.1 US qts, 5.9 Imp. qts) |
| Dry fill | 8.4 liters (8.9 US qts, 7.4 Imp. qts) |
Install the oil filler cap.
| 18. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's FULL line.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the LOW line, add TOYOTA SLLC to the FULL line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,500 to 3,000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the FULL line.
If the coolant level is below the LOW line, add TOYOTA SLLC to the FULL line.
| 19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 20. INSPECT FOR OIL LEAK |
Start the engine, and check that there are no oil leaks after performing maintenance.
| 21. INSPECT FOR COOLANT LEAK |
Check for engine coolant leaks .
| 22. INSTALL NO. 2 ENGINE UNDER COVER |
Install the under cover with the 2 bolts.
| 23. INSTALL NO. 1 ENGINE UNDER COVER |
Install the under cover with the 4 bolts.