FUEL FILTER > REPLACEMENT |
| 1. REMOVE FUEL FILTER ELEMENT ASSEMBLY |
![]() |
Disconnect the clogging switch connector.
Move the clip to disconnect the hose connected to the filter inlet.
Connect a hose to the drain cock. Place the other side of the same hose into a container.
Loosen the drain cock to drain fuel (approximately 50 cc (3.0 cu. in.)).
Tighten the drain cock.
![]() |
Using a screwdriver as a lever, loosen the fastener nut until it can be loosened by hand.
![]() |
Fully loosen the fastener nut by hand.
![]() |
To remove the cap, pull up one side of the cap, and then lift it off.
Remove the fuel filter element from the case.
Remove the case O-ring.
| 2. INSTALL FUEL FILTER ELEMENT ASSEMBLY |
![]() |
Attach 2 new O-rings to a new fuel filter element and a new O-ring to the case.
Install the fuel filter element to the case.
![]() |
Align the mark on the cap and the mark on the case.
![]() |
Push the cap onto the case by hand.
![]() |
Turn the fastener nut until a "click" sound is heard.
Measure the distance between the marks on the cap and case, and the clearance between the cap and case.
![]() |
Connect the hose to the filter inlet and install the clip as shown in the illustration.
| 3. RESET FUEL SYSTEM WARNING LIGHT |
Turn the ignition switch to ON.
![]() |
After turning the ignition switch to ON, connect the clogging switch connector no sooner than 3 seconds have passed but no later than 60 seconds have passed.
Check that the combination meter's fuel system warning light turns off.
| 4. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Check if the engine starts.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2
| *a | Reference (Active Test Operation) |
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| 5. INSPECT FOR FUEL LEAK |
Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.
Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.
Disconnect the return hose from the common rail.
Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.
Connect the intelligent tester to the DLC3.
Start the engine and push the intelligent tester main switch on.
Select the Fuel Leak test from the Active Test mode on the intelligent tester.
If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.
Check that there are no leaks from any part of the fuel system.
Reconnect the return hose to the common rail.