Home › ENGINE · 1GR-FE › FUEL › FUEL INJECTOR

FUEL INJECTOR > INSPECTION

for Preparation Click here



1. INSPECT INJECTOR ASSEMBLY
  1. Measure the resistance between the terminals.

    Standard resistance:
    11.6 to 12.4 Ω at 20°C (68°F)

    If the result is not as specified, replace the injector assembly.



2. INSPECT INJECTION VOLUME AND LEAKAGE


    A267747E01
  1. Check the injector injection.

    CAUTION:
    1. This test involves high-pressure fuel and electricity.
    2. Take every precaution regarding safe handling of both the fuel and the electrical parts.
    3. Perform this test in a safe area, and avoid any sparks or flame.
    4. Do not smoke.


    1. Assemble SST as shown in the illustration.

      SST
      09268-31014   (09268-41091, 09268-41120, 09268-41500, 09268-41700, 95336-08070)

    2. Discharge the fuel system pressure.

    3. Disconnect the fuel inlet hose (fuel tube connector) from the fuel filter.

    4. Remove the bolt and disconnect the fuel pressure regulator from the fuel delivery pipe.

      NOTICE:
      Do not disconnect the No. 2 fuel hose from the fuel pressure regulator.



    5. A267748E01
    6. Connect SST to the fuel filter.

      SST
      09268-31014   (09268-41500)

      CAUTION:
      Always read the precautions before connecting the fuel tube connector.



    7. A267749E01
    8. Install the fuel pressure regulator to SST (union) with the 2 bolts.

      SST
      09268-31014   (09268-41091, 09268-41700, 95336-08070)

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    9. Connect the fuel return hose to the fuel outlet of the pressure regulator.



    10. A267750E01
    11. Install a new O-ring to the injector.

    12. Connect SST (adapter and hose) to the injector, and hold the injector and adapter with SST (clamp).

      SST
      09268-31014   (09268-41141, 09268-41410, 09268-41700, 95336-08070)



    13. A267752E01
    14. Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).

      SST
      09268-31014   (09268-41800)

      NOTICE:
      1. As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.
      2. Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.

      HINT:
      When removing SST (tie band), disengage the lock.

    15. Check that SST (clamp) and SST (adapter) cannot be easily separated.

    16. Install a vinyl tube to the injector.

      CAUTION:
      Install a suitable vinyl tube to the injector to contain any gasoline spray.

    17. Put the injector into a graduated cylinder.

      HINT:
      Install a suitable vinyl tube onto the injector to contain any gasoline spray.

    18. Operate the fuel pump.



    19. A267751E01
    20. Connect SST (wire) to the injector and the battery for 15 seconds, and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.

      SST
      09842-30080  

      Standard volume:
      Injection Volume
      Difference Between Each Injector
      76 to 91 cm3 (4.6 to 5.5 cu in.) per 15 seconds
      15 cm3 (0.9 cu in.) or less

      NOTICE:
      1. Make sure that SST (EFI inspection wire H) is securely connected.
      2. Always turn the voltage on and off on the battery side, not the fuel pump side.

      If the result is not as specified, replace the injector assembly.



    A075916E02
  1. Check the rate of fuel leakage.

    1. In the condition above, disconnect the tester probes of SST (wire) from the battery and check the rate of fuel leakage from the injector.

      Standard fuel leakage:
      1 drop or less per 12 minutes