DTC P0100 Mass Air Flow Circuit Malfunction |
DTC P0102 Mass Air Flow Circuit Low |
DTC P0103 Mass Air Flow Circuit High |

| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| 3 seconds after engine is started | Mass air flow meter voltage is 0.2 V or less, or 4.9 V or more with the engine speed at 4000 rpm or less for 3 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| 3 seconds after engine is started | Mass air flow meter voltage is 0.2 V or less with the engine speed at 4000 rpm or less for 3 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| 3 seconds after engine is started | Mass air flow meter voltage is 4.9 V or more with the engine speed at 4000 rpm or less for 3 seconds (1 trip detection logic). |
|
| DTC No. | Data List |
| P0100 | MAF |
| P0102 | |
| P0103 |
| Air Flow Value (gm/s) | Malfunction |
| Approximately 0.0 |
|
| 167.5 or more | Open in EVG circuit |

| 1.INSPECT MASS AIR FLOW METER (POWER SOURCE CIRCUIT) |
![]() |
Disconnect the mass air flow meter connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A4-1 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Mass Air Flow Meter) |
Reconnect the mass air flow meter connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A4-3 - E6-24 (VG) | Always | Below 1 Ω |
| A4-2 - E6-32 (EVG) | Always | Below 1 Ω |
| A4-3 or E6-24 (VG) - Body ground | Always | 10 kΩ or higher |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
|
| ||||
|
| ||||
| 3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY) |
Disconnect the mass air flow meter connector.
Remove the No. 1 integration relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A4-1 - 1J-5 | Always | Below 1 Ω |
| A4-1 or 1J-5 - Body ground | Always | 10 kΩ or higher |
Reconnect the mass air flow meter connector.
Reinstall the No. 1 integration relay.
|
| ||||
|
| ||||
| 4.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
| ||||
| 5.CHECK ECM POWER SOURCE CIRCUIT |
Check the ECM power source circuit (Click here).
|
| ||||
| 6.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0100, P0102 AND/OR P0103) |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Start the engine and wait for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0100, P0102 and/or P0103 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 8.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Start the engine and wait for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||