DTC P0200 Injector Circuit / Open |

| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Idling for 5 seconds | Open or short in the injector driver or fuel injector circuit (1 trip detection logic). |
|



| 1.CHECK ENGINE CRANKING CONDITION |
Check the engine cranking condition.
| Result | Proceed to |
| Engine does not start*1 | A |
| Engine starts, but idling is rough*2 | B |
| Except above | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK ECM |
![]() |
Check the waveform of the ECM connectors using an oscilloscope.
Check the waveform of the injector driver (EDU) connectors using an oscilloscope.
| Tester Connection | Condition | Specified Condition |
| E7-24 (#1) - E6-7 (E1) | Cranking | Correct waveform is as shown |
| E7-23 (#2) - E6-7 (E1) | Cranking | Correct waveform is as shown |
| E7-22 (#3) - E6-7 (E1) | Cranking | Correct waveform is as shown |
| E7-21 (#4) - E6-7 (E1) | Cranking | Correct waveform is as shown |
| *a | Component with harness connected (ECM) |
|
| ||||
| OK | |
| 3.CHECK TERMINAL VOLTAGE INJECTOR DRIVER POWER SOURCE |
![]() |
Disconnect the injector driver connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| I17-2 (+B) - I17-3 (GND) | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| I14-2 (+B) - I14-3 (GND) | Ignition switch ON | 11 to 14 V |
| *A | for RHD with 4WD |
| *B | except RHD with 4WD |
| *a | Front view of wire harness connector (to Injector Driver) |
Reconnect the injector driver connectors.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM) |
Disconnect the injector driver connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I16-4 (#10) - E7-24 (#1) | Always | Below 1 Ω |
| I16-8 (#20) - E7-23 (#2) | Always | Below 1 Ω |
| I16-7 (#30) - E7-22 (#3) | Always | Below 1 Ω |
| I16-3 (#40) - E7-21 (#4) | Always | Below 1 Ω |
| I16-5 (INJF) - E7-25 (INJF) | Always | Below 1 Ω |
| I16-4 (#10) or E7-24 (#1) - Body ground | Always | 10 kΩ or higher |
| I16-8 (#20) or E7-23 (#2) - Body ground | Always | 10 kΩ or higher |
| I16-7 (#30) or E7-22 (#3) - Body ground | Always | 10 kΩ or higher |
| I16-3 (#40) or E7-21 (#4) - Body ground | Always | 10 kΩ or higher |
| I16-5 (INJF) or E7-25 (INJF) - Body ground | Always | 10 kΩ or higher |
Reconnect the injector driver connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 5.REPLACE INJECTOR DRIVER |
Replace the injector driver (Click here).
|
| ||||
| 6.READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 to #4) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.
Start the engine.
Read the Injection Feedback Val #1 to #4 values while idling the engine.
| Item | Engine Speed* | Reference Value |
| Injection Feedback Val #1 to #4 | Idling | +3.0 mm3/st or less |
| NEXT | |
| 7.INSPECT INJECTOR ASSEMBLY (RESISTANCE) |
![]() |
Disconnect the fuel injector connectors.
Measure the resistance of the fuel injector
| *a | Component without harness connected (Fuel Injector) |
Reconnect the fuel injector connectors.
|
| ||||
| OK | |
| 8.INSPECT INJECTOR DRIVER |
![]() |
Disconnect the fuel injector connectors for all cylinders.
Check the waveform of the fuel injector connectors using an oscilloscope.
| Tester Connection | Condition | Specified Condition |
| F4-1 - F4-2 | Cranking | Voltage increases by 50 V or more |
| F5-1 - F5-2 | Cranking | Voltage increases by 50 V or more |
| F6-1 - F6-2 | Cranking | Voltage increases by 50 V or more |
| F7-1 - F7-2 | Cranking | Voltage increases by 50 V or more |
| *a | Front view of wire harness connector (to Fuel Injector) |
|
| ||||
| OK | |
| 9.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER |
Replace the injector assembly (Click here).
| NEXT | |
| 10.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 11.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING |
Register the injector compensation code .
Perform the injector pilot quantity learning .
|
| ||||
| 12.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 13.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER) |
Disconnect the injector assembly connectors.
Disconnect the injector driver connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F4-1 - I17-1 (IJ1+) | Always | Below 1 Ω |
| F4-2 - I15-6 (IJ1-) | Always | Below 1 Ω |
| F5-1 - I17-6 (IJ2+) | Always | Below 1 Ω |
| F5-2 - I15-4 (IJ2-) | Always | Below 1 Ω |
| F6-1 - I17-5 (IJ3+) | Always | Below 1 Ω |
| F6-2 - I15-2 (IJ3-) | Always | Below 1 Ω |
| F7-1 - I15-3 (IJ4+) | Always | Below 1 Ω |
| F7-2 - I15-5 (IJ4-) | Always | Below 1 Ω |
| F4-1 or I17-1 (IJ1+) - Body ground | Always | 10 kΩ or higher |
| F4-2 or I15-6 (IJ1-) - Body ground | Always | 10 kΩ or higher |
| F5-1 or I17-6 (IJ2+) - Body ground | Always | 10 kΩ or higher |
| F5-2 or I15-4 (IJ2-) - Body ground | Always | 10 kΩ or higher |
| F6-1 or I17-5 (IJ3+) - Body ground | Always | 10 kΩ or higher |
| F6-2 or I15-2 (IJ3-) - Body ground | Always | 10 kΩ or higher |
| F7-1 or I15-3 (IJ4+) - Body ground | Always | 10 kΩ or higher |
| F7-2 or I15-5 (IJ4-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| F4-1 - I14-1 (IJ1+) | Always | Below 1 Ω |
| F4-2 - I15-6 (IJ1-) | Always | Below 1 Ω |
| F5-1 - I14-6 (IJ2+) | Always | Below 1 Ω |
| F5-2 - I15-4 (IJ2-) | Always | Below 1 Ω |
| F6-1 - I14-5 (IJ3+) | Always | Below 1 Ω |
| F6-2 - I15-2 (IJ3-) | Always | Below 1 Ω |
| F7-1 - I15-3 (IJ4+) | Always | Below 1 Ω |
| F7-2 - I15-5 (IJ4-) | Always | Below 1 Ω |
| F4-1 or I14-1 (IJ1+) - Body ground | Always | 10 kΩ or higher |
| F4-2 or I15-6 (IJ1-) - Body ground | Always | 10 kΩ or higher |
| F5-1 or I14-6 (IJ2+) - Body ground | Always | 10 kΩ or higher |
| F5-2 or I15-4 (IJ2-) - Body ground | Always | 10 kΩ or higher |
| F6-1 or I14-5 (IJ3+) - Body ground | Always | 10 kΩ or higher |
| F6-2 or I15-2 (IJ3-) - Body ground | Always | 10 kΩ or higher |
| F7-1 or I15-3 (IJ4+) - Body ground | Always | 10 kΩ or higher |
| F7-2 or I15-5 (IJ4-) - Body ground | Always | 10 kΩ or higher |
Reconnect the injector assembly connectors.
Reconnect the injector driver connectors.
|
| ||||
| OK | |
| 14.REPLACE INJECTOR DRIVER |
Replace the injector driver (Click here).
|
| ||||
| 15.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 10 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||