DTC P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state. | The throttle motor activation duty is more than a specified value for 30 seconds (1 trip detection logic). |
|
| DTC No. | Data List |
| P0488 | Actual Throttle Position |
| Condition | Throttle Valve Position |
| Moment when accelerator pedal is depressed further or released at 3000 rpm | Throttle valve opening angle varies smoothly |


| 1.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE) |
![]() |
Disconnect the throttle control motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| T2-2 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Throttle Control Motor) |
Reconnect the throttle control motor connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT) |
Disconnect the throttle control motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T2-3 (RSC) - Body ground | Always | Below 1 Ω |
Reconnect the throttle control motor connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM) |
Disconnect the throttle control motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T2-1 (RSO) - E6-4 (LUSL) | Always | Below 1 Ω |
| T2-1 (RSO) or E6-4 (LUSL) - Body ground | Always | 10 kΩ or higher |
Reconnect the throttle control motor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 4.REPLACE DIESEL THROTTLE BODY ASSEMBLY |
Replace the diesel throttle body assembly (Click here).
Turn the ignition switch to ON.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and wait for 10 seconds or more.
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488) |
Clear the DTCs (Click here).
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Start the engine.
Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0488 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 6.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 7.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - BATTERY) |
Repair or replace the harness or connector.
|
| ||||
| 8.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm, and then lower it.
Confirm that the DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P0488.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm again, and then idle the engine for 5 minutes.
| NEXT | ||
| ||