Home › TRANSMISSION · A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0717    Input Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

This sensor detects the rotation speed of the turbine, which shows the input revolution of the transmission. By comparing the input speed signal (NT) with the counter gear speed sensor signal (SP2), the ECM detects the shift timing of the gears and controls the engine torque and hydraulic pressure according to various conditions. As a result, smooth gear shifting is achieved.

G036793E04


DTC Code
DTC Detection Condition
Trouble Area
P0717
All conditions below are detected for 5 sec. or more (1 trip detection logic):
(a) Gear changes not performed
(b) Gear position: 4th or 5th
(c) Transmission input shaft rpm: less than 300 rpm
(d) Transmission output shaft rpm: 1000 rpm or more
(e) Park/Neutral position switch
  1. NSW input signal is OFF
  2. R input signal is OFF
  3. L input signal is OFF
(f) Shift solenoid valves and park/neutral position switch are operating normally
  1. Open or short in speed sensor (NT) circuit
  2. Speed sensor (NT)
  3. ECM
  4. Automatic transmission (clutch, brake, gear, etc.)

MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor (NT) or is output only a little. The NT terminal of the ECM detects the pulse signal from the speed sensor (NT) (input RPM). The ECM outputs a gear shift signal by comparing the speed sensor (NT) signal with the speed sensor (SP2) signal.
While the vehicle is operating in 4th or 5th gear with the shift lever on D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is 1000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.

HINT:
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is approximately 50 km/h (31 mph) or more.


WIRING DIAGRAM


C155187E50


INSPECTION PROCEDURE

HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

  1. Warm up the engine.
  2. Turn the ignition switch OFF.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch ON and push the tester main switch ON.
  5. Enter the following menus: Powertrain / Engine and ECT / Data List.
  6. Follow the instructions on the tester and read the Data List.

Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
SPD (NT)
Input turbine speed/
Min.: 0 rpm
Max.: 12,750 rpm

HINT:
  1. Lock-up ON (after warming up engine):
    Input turbine speed (NT) equal to the engine speed.
  2. Lock-up OFF (idling with shift lever on N):
    Input turbine speed (NT) is nearly equal to engine speed.

Data is displayed in increments of 50 rpm

CAUTION:
In the table above, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
  1. SPD (NT) is always 0 rpm while driving:
    Open or short in the sensor or circuit.
  2. SPD (NT) is always more than 0 rpm and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:
    Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

1.INSPECT SPEED SENSOR (INSTALLATION)


    BR03795E15
  1. Check the speed sensor (NT) installation.

    OK:
    Installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



NG
SECURELY INSTALL SPEED SENSOR OR REPLACE SPEED SENSOR
OK


2.INSPECT SPEED SENSOR (NT)
C058536E05
  1. Disconnect the T27 sensor connector from the transmission.



  1. Measure the resistance of the sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω


    HINT:
    A110972E01
    Reference: Inspect using an oscilloscope.
    Check the waveform of the ECM connector.

    OK:
    Refer to illustration
    Item
    Content
    Tester Connection
    E16-35 (NT+) - E16-27 (NT-)
    Tool Setting
    1 V/DIV., 2 msec./DIV.
    Condition
    Engine is idling (P or N position)



NG
REPLACE SPEED SENSOR (NT)
OK


3.CHECK WIRE HARNESS (SPEED SENSOR (NT) - ECM)


    G035616E01
  1. Disconnect the E16 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E16-35 (NT+) - E16-27 (NT-)
    20°C (68°F)
    560 to 680 Ω
    E16-35 (NT+) - Body ground
    Always
    10 kΩ or higher
    E16-27 (NT-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM