QUARTER WINDOW GLASS > INSTALLATION |
| 1. INSTALL QUARTER WINDOW ASSEMBLY RH |
![]() |
Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.
![]() |
Install a new spacer to the vehicle body.
Using a brush or sponge, apply primer G to the contact surface of a new quarter window glass.

Apply adhesive to the quarter window glass.
Cut off the tip of the cartridge nozzle as shown in the illustration.

| Area | Specified Condition |
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| c | 13.0 mm (0.512 in.) |
| d | 12.7 mm (0.500 in.) |
| Temperature | Usage Time Frame |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the quarter window glass as shown in the illustration.
Install the quarter window glass to the vehicle body.
Hold the quarter window glass in place securely with protective tape or equivalent until the adhesive hardens.
Lightly press the front surface of the glass to ensure a close fit.
![]() |
Using a scraper, remove any excess or protruding adhesive.
| Temperature | Minimum Time Prior to Driving Vehicle |
| 35°C (95°F) | 1 hour 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
| 2. INSTALL ROOF HEADLINING ASSEMBLY |
![]() |
Place the roof headlining into the vehicle as shown in the illustration.
for LHD:
Attach the 5 fasteners to install the roof headlining.
Install the 7 clips.
Connect the connectors and attach the 4 clamps.
for RHD:
Attach the 5 fasteners to install the roof headlining.
Install the 7 clips.
Connect the connectors and attach the 5 clamps.
Attach the 4 clamps to the front pillar.
| 3. INSTALL NO. 1 ROOM LIGHT ASSEMBLY |
![]() |
Connect the light connector.
Install the room light with the 2 screws.
Attach the 4 claws to install the lens
| 4. INSTALL ASSIST GRIP |
Install the assist grip with the 2 screws.
Attach the 4 claws to close the 2 covers.
| 5. INSTALL INNER UPPER ROOF SIDE GARNISH RH |
| 6. INSTALL QUARTER PILLAR GARNISH RH |
| 7. INSTALL QUARTER INSIDE TRIM BOARD RH |
Detach the 8 claws and 10 clips to install the quarter inside trim board.
Install the clip.
Connect the rear No. 2 seat outer belt floor anchor with the bolt.
Connect the rear No. 1 seat outer belt floor anchor with the bolt.
Attach the 2 claws to install the outer lap belt anchor cover.
| 8. CONNECT REAR NO. 2 SEAT BELT ASSEMBLY OUTER RH |
![]() |
Connect the seat belt's floor anchor with the bolt.
![]() |
Install the belt outer anchor cover.
| 9. CONNECT REAR NO. 1 SEAT BELT ASSEMBLY OUTER RH |
![]() |
Connect the seat belt's floor anchor with the bolt.
![]() |
Install the belt outer anchor cover.
| 10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
| 11. INSTALL REAR DOOR SCUFF PLATE RH |
| 12. INSTALL BACK DOOR SCUFF PLATE |
Attach the 4 claws, 2 guides and 6 clips to install the back door scuff plate.
| 13. INSTALL REAR NO. 2 SEAT ASSEMBLY RH |
Fully tilt the seatback forward.
![]() |
Place the seat onto the lock striker.
Tighten the bolt on the rear side of the seat.
Tighten the bolt on the front side of the seat.
Fully lock the seat to the lock striker.
| 14. INSTALL REAR SEAT REAR BRACKET COVER RH |
Attach the hook to install the bracket cover.
Install the screw.
Return the seatback to the upright position.
| 15. INSTALL REAR SEAT FRONT BRACKET COVER RH |
![]() |
Attach the hook to install the bracket cover.
Install the screw.
| 16. CHECK FOR LEAKS AND REPAIR |
Conduct a leak test after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.