Home › BODY › SEAT › REAR NO. 2 SEAT ASSEMBLY

REAR NO. 2 SEAT ASSEMBLY > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the RH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).

CAUTION:
Wear protective gloves. Sharp areas on the seatback frames and seat cushion frame may injure your hands,



1. INSTALL NO. 2 SEAT LEG PLATE
  1. Install the plate with the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



2. INSTALL REAR NO. 2 SEAT CUSHION COVER


    B133279E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 4 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. Install the seat cushion cover (with pad) to the seat cushion frame with the hook.



3. INSTALL REAR SEAT CUSHION UNDER CLOTH


4. INSTALL NO. 1 SEAT CUSHION CARPET


    B089770E01
  1. Set the carpet onto the seat cushion.

  1. Using a tacker, install the carpet to the seat cushion with the 4 tack pins and 2 clips, as shown in the illustration.

    NOTICE:
    Do not substitute other metal parts for tack pins.



5. INSTALL NO. 2 SEAT LEG SUB-ASSEMBLY RH


    B118020
  1. Install the leg with the 2 bolts and No. 3 seat cushion spring.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



6. INSTALL REAR NO. 2 SEAT BELT SUB-ASSEMBLY INNER RH


B089697E01
  1. Install the seat belt with the nut as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and the protruding parts of the floor panel.



7. INSTALL REAR SEAT LEG COVER


    B089767E02
  1. Attach the 2 claws to install the leg cover.

  1. Install the 3 screws.



8. INSTALL NO. 2 SEAT CUSHION COVER RH


    B089765E01
  1. Pass the fold seat stopper band through the hole in the No. 2 seat cushion cover. Then install the fold seat stopper band to the seat cushion frame with the screw.

  1. Install the No. 2 seat cushion cover with the 5 screws.

  1. Install the rear No. 2 seat cushion cover to the No. 2 seat cushion cover.



    B118018E01
  1. Attach the 14 claws and hooks.



9. INSTALL REAR NO. 2 SEAT COVER RH


    B118017E01
  1. Pass the fold seat stopper band through the hole in the rear No. 2 seat cover RH.

  1. Install the rear No. 2 seat cover RH with the screw.

  1. Fold the fold seat stopper band and install the 2 lock release buttons as shown in the illustration.



10. INSTALL REAR SEAT HINGE COVER


    B089762E01
  1. Attach the 2 claws to install the hinge cover.

  1. Install the 2 screws.



11. INSTALL NO. 3 SEAT OUTER REAR LEG SUB-ASSEMBLY RH
  1. Install the leg with the 2 plates and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



12. INSTALL NO. 3 SEAT OUTER FRONT LEG SUB-ASSEMBLY RH
  1. Install the leg with the 2 plates and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



13. INSTALL REAR NO. 2 SEATBACK COVER


    B118016E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. Install the seatback cover (with pad) to the seatback frame.



    B085727E01
  1. Install the 2 headrest supports.



    B118015E01
  1. Attach the hooks and close the fastening tape.



14. INSTALL REAR NO. 2 SEATBACK ASSEMBLY


    B086030E02
  1. LH side:
    Install the seatback with the plate, spacer and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. RH side:
    Install the seatback with the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



15. INSTALL REAR NO. 2 SEAT RECLINING COVER RH


B085723E01
  1. Install the reclining cover with the 2 screws.



16. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH


B085725E01
  1. Install the release handle with the screw.



17. INSTALL REAR SEAT CUSHION LOWER HINGE COVER RH


B085724E01
  1. Install the hinge cover with the 2 screws.



18. INSTALL REAR NO. 2 SEAT HEADREST ASSEMBLY RH