Home › BODY › SEAT › REAR NO. 1 SEAT ASSEMBLY (for RH Side)

REAR NO. 1 SEAT ASSEMBLY (for RH Side) > REASSEMBLY

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).

CAUTION:
Wear protective gloves. Sharp areas on the seatback frame and seat cushion frame may injure your hands.



1. INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY


    B118292
  1. Install the band to the seat cushion frame.



2. INSTALL REAR NO. 1 SEAT CUSHION COVER


    B133275E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 4 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. Install the seat cushion cover (with pad) to the seat cushion frame.

    HINT:
    Make sure that the stopper band is not inside the cushion frame.



3. INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY LH


B120607E02
  1. Install the seat belt LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the seat.



4. INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY CENTER


B120606E02
  1. Install the seat belt center with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the seat.



5. INSTALL REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY RH


    B118289E01
  1. Attach the 2 claws and install the under cover with the 4 screws.



    B118294E01
  1. Attach the 11 claws and hooks. Then install the seat cushion cover to the under cover.



6. INSTALL REAR NO. 1 SEAT CUSHION ASSEMBLY
  1. Using a T40 "torx" socket, install the 2 seat tracks to the seat cushion with the 2 "torx" bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Install the seat track adjusting handle.

  1. Lift up the seat track adjusting handle and move the seat track to the foremost position.



  1. Using a T40 "torx" socket, tighten the 4 "torx" bolts on the rear side of the seat track.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



    B118293



7. INSTALL REAR NO. 1 SEAT TRACK BRACKET


    B118301
  1. Using a T40 "torx" socket, install the bracket with the 2 "torx" bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



8. INSTALL REAR SEAT LOCK ASSEMBLY RH
  1. Install the lock control cable to the lock with the E-ring and plate.



    B118299
  1. Using a T40 "torx" socket, install the lock with the 2 "torx" bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Connect the lock control cable to the seat track.

  1. Install the support spring.



9. INSTALL REAR SEAT LOCK ASSEMBLY LH


    B122484
  1. Using a T40 "torx" socket, install the lock with the plate and 2 "torx" bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



    B118306
  1. Connect the lock control cable to the lock as shown in the illustration.

  1. Install the support spring.



10. INSTALL RECLINING RELEASE HANDLE SUB-ASSEMBLY


    B118304
  1. Install the release handle to the rear seat lock through the hole in the rear seat cushion under cover.

  1. Install the seat track adjusting handle.



11. INSTALL REAR SEAT HINGE ASSEMBLY LH


    B118297
  1. Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



12. INSTALL REAR SEAT HINGE ASSEMBLY RH
  1. Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



13. INSTALL REAR NO. 2 SEAT LOCK COVER RH


    B118296
  1. Install the lock cover with the 2 screws.



14. INSTALL REAR NO. 1 SEAT LOCK COVER RH


    B118311E01
  1. Attach the rear seat lock control cable to the lock cover's claw.

  1. Install the lock cover with the 7 screws.

  1. Install the reclining remote control lever knob with the screw.



15. INSTALL REAR NO. 1 SEAT BELT ASSEMBLY INNER RH
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



16. INSTALL REAR SEAT ARMREST ARM LH
  1. Install the arm with the nut.



17. INSTALL REAR SEAT ARMREST ARM RH
  1. Install the arm with the nut.



18. INSTALL REAR SEATBACK BOARD RH


19. INSTALL REAR NO. 1 SEATBACK COVER

NOTICE:
  1. Be careful not to damage the cover.
  2. When installing the hog rings, avoid wrinkling the cover.



    B118287E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with 2 new hog rings.

  1. Install the seatback cover (with pad) to the seatback frame.

  1. Attach the 4 claws to install the 2 headrest supports.



    B128874E01
  1. Using hog ring pliers, install 10 new hog rings.



    B086198E01
  1. Install the armrest with the 2 bushes and 2 bolts.



    B118308E01
  1. Close the zipper and attach the hooks.



20. INSTALL REAR NO. 1 SEATBACK ASSEMBLY


    B089778E01
  1. Install the seatback with the 4 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



21. INSTALL REAR NO. 1 SEAT RECLINING COVER RH


    B089782E01
  1. Attach the 4 claws to install the reclining cover.

  1. Install the screw.



22. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH


    B086040E01
  1. Install the release handle with the screw.



23. INSTALL REAR NO. 1 SEAT RECLINING COVER LH


    B089780E01
  1. Attach the 3 claws to install the reclining cover.

  1. Install the screw.



24. INSTALL REAR SEAT HEADREST ASSEMBLY