REAR NO. 1 SEAT ASSEMBLY (for LH Side) > DISASSEMBLY |
| 1. REMOVE REAR SEAT HEADREST ASSEMBLY |
| 2. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH |
![]() |
Remove the screw and release handle.
| 3. REMOVE REAR NO. 1 SEAT RECLINING COVER LH |
![]() |
Remove the screw.
Using a screwdriver, detach the 4 claws and remove the reclining cover.
| 4. REMOVE REAR NO. 1 SEAT RECLINING COVER RH |
![]() |
Remove the screw.
Using a screwdriver, detach the 3 claws and remove the reclining cover.
| 5. REMOVE REAR NO. 1 SEATBACK ASSEMBLY |
![]() |
Remove the 4 bolts and seatback.
| 6. REMOVE REAR NO. 1 SEATBACK COVER |
![]() |
Using a screwdriver, detach the hooks.
Open the zipper.
Roll up the seatback cover.
![]() |
Detach the 4 claws and remove the 2 headrest supports.
Remove the seatback cover (with pad) from the seatback frame.
![]() |
Remove the 2 hog rings and the seatback cover from the seatback pad.
| 7. REMOVE REAR SEATBACK BOARD LH |
| 8. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH |
Remove the bolt and belt.
| 9. REMOVE REAR NO. 1 SEAT LOCK COVER LH |
![]() |
Remove the screw and the reclining remote control lever knob.
Remove the 7 screws.
Raise the lock cover and remove the rear seat lock control cable from the lock cover's claw. Then remove the lock cover.
| 10. REMOVE REAR NO. 2 SEAT LOCK COVER LH |
![]() |
Remove the 2 screws and lock cover.
| 11. REMOVE REAR SEAT HINGE ASSEMBLY LH |
![]() |
Remove the 2 nuts and hinge.
| 12. REMOVE REAR SEAT HINGE ASSEMBLY RH |
Remove the 2 nuts and hinge.
| 13. REMOVE RECLINING RELEASE HANDLE SUB-ASSEMBLY |
Remove the seat track adjusting handle.
![]() |
Remove the release handle from the rear seat lock through the hole in the rear seat cushion under cover.
| 14. REMOVE REAR SEAT LOCK ASSEMBLY LH |
![]() |
Using a screwdriver, remove the support spring.
Disconnect the lock control cable from the seat track.
Using a T40 "torx" socket, remove the 2 "torx" bolts and lock (together with the lock control cable).
Remove the E-ring, plate and lock control cable from the lock.
| 15. REMOVE REAR SEAT LOCK ASSEMBLY RH |
![]() |
Using a screwdriver, remove the support spring and disconnect the lock control cable as shown in the illustration.
![]() |
Using a T40 "torx" socket, remove the 2 "torx" bolts, plate and lock.
| 16. REMOVE REAR NO. 1 SEAT TRACK BRACKET |
![]() |
Using a T40 "torx" socket, remove the 2 "torx" bolts and bracket.
| 17. REMOVE REAR NO. 1 SEAT CUSHION ASSEMBLY |
Lift up the seat track adjusting handle and move the seat track to the foremost position.
Using a T40 "torx" socket, remove the 4 "torx" bolts.
Lift up the seat track adjusting handle and move the seat track to the rearmost position.
Using a screwdriver, push down the handle stopper and detach the claws. Then remove the seat track adjusting handle.
Using a T40 "torx" socket, remove the 2 "torx" bolts and seat cushion from the 2 seat tracks.

| 18. REMOVE REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY LH |
![]() |
Using a screwdriver, detach the 8 claws and hooks.
Remove the under cover from the seat cushion cover. Then hold back the seat cushion cover so that the 5 screws are visible.
![]() |
Remove the 5 screws.
Detach the 2 claws and remove the under cover.
| 19. REMOVE REAR NO. 1 SEAT CUSHION COVER |
Remove the seat cushion cover (with pad) from the seat cushion frame.
![]() |
Remove the 4 hog rings and seat cushion cover from the seat cushion pad.
| 20. REMOVE NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY |
![]() |
Pull the band in the direction indicated by the black arrow in the illustration. Then remove the band.