Home › BODY › SEAT › REAR NO. 1 SEAT ASSEMBLY (for LH Side)

REAR NO. 1 SEAT ASSEMBLY (for LH Side) > REASSEMBLY

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).

CAUTION:
Wear protective gloves. Sharp areas on the seatback frame and seat cushion frame may injure your hands.



1. INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY


    B118269
  1. Install the band to the seat cushion frame.



2. INSTALL REAR NO. 1 SEAT CUSHION COVER


    B133273E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 4 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. Install the seat cushion cover (with pad) to the seat cushion frame.

    HINT:
    Make sure that the seat stopper band is not inside the cushion cover.



3. INSTALL REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY LH


    B118267
  1. Attach the 2 claws and install the under cover with the 5 screws.



    B118275E01
  1. Attach the 8 claws and hooks. Then install the seat cushion cover to the under cover.



4. INSTALL REAR NO. 1 SEAT CUSHION ASSEMBLY
  1. Using a T40 "torx" socket, install the 2 seat tracks to the seat cushion with the 2 "torx" bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Install the seat track adjusting handle.

  1. Lift up the seat track adjusting handle and move the seat track to the foremost position.



  1. Using a T40 "torx" socket, tighten the 4 "torx" bolts on the rear side of the seat track.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



    B118270E01



5. INSTALL REAR NO. 1 SEAT TRACK BRACKET


    B118272
  1. Using a T40 "torx" socket, install the bracket with the 2 "torx" bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



6. INSTALL REAR SEAT LOCK ASSEMBLY RH


    B122485
  1. Using a T40 "torx" socket, install the lock with the plate and 2 "torx" bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



    B118279
  1. Connect the lock control cable to the lock.

  1. Install the support spring.



7. INSTALL REAR SEAT LOCK ASSEMBLY LH
  1. Install the lock control cable to the lock with the E-ring and plate.

  1. Using a T40 "torx" socket, install the lock with the 2 "torx" bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



    B119373
  1. Connect the lock control cable to the lock as shown in the illustration.

  1. Install the support spring.



8. INSTALL RECLINING RELEASE HANDLE SUB-ASSEMBLY


    B118276
  1. Install the release handle to the rear seat lock through the hole in the rear seat cushion under cover.

  1. Install the seat track adjusting handle.



9. INSTALL REAR SEAT HINGE ASSEMBLY LH


    B118283
  1. Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



10. INSTALL REAR SEAT HINGE ASSEMBLY RH
  1. Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



11. INSTALL REAR NO. 2 SEAT LOCK COVER LH


    B118282
  1. Install the lock cover with the 2 screws.



12. INSTALL REAR NO. 1 SEAT LOCK COVER LH


    B118281E01
  1. Attach the rear seat lock control cable to the lock cover's claw.

  1. Install the lock cover with the 7 screws.

  1. Install the reclining remote control lever knob with the screw.



13. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



14. INSTALL REAR SEATBACK BOARD LH


15. INSTALL REAR NO. 1 SEATBACK COVER

NOTICE:
  1. Be careful not to damage the cover.
  2. When installing the hog rings, avoid wrinkling the cover.



    B118265E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with 2 new hog rings.

  1. Install the seatback cover (with pad) to the seatback frame.

  1. Install the 2 headrest supports.



    B118263E01
  1. Close the zipper and attach the hooks.



16. INSTALL REAR NO. 1 SEATBACK ASSEMBLY


    B089779E01
  1. Install the seatback with the 4 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



17. INSTALL REAR NO. 1 SEAT RECLINING COVER RH


    B089781E01
  1. Attach the 3 claws to install the reclining cover.

  1. Install the screw.



18. INSTALL REAR NO. 1 SEAT RECLINING COVER LH


    B089783E01
  1. Attach the 4 claws to install the reclining cover.

  1. Install the screw.



19. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    B086769E01
  1. Install the release handle with the screw.



20. INSTALL REAR SEAT HEADREST ASSEMBLY