Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Driver Side Power Window Manual Function does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

If the manual up/down function does not operate, a malfunction may be present in the power window regulator master switch assembly, front door window regulator sub-assembly (for driver side) or wire harness.

WIRING DIAGRAM


B276858E05


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)


    B276330E27
  1. Disconnect the P6 power window regulator master switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    P6-7 (BW) - Body ground
    Always
    11 to 14 V
    P6-6 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P6-1 (E) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (FOR DRIVER SIDE)


    B276330E28
  1. Disconnect the P6 power window regulator master switch assembly connector.

  1. Check operation of the front door window regulator sub-assembly (for driver side).

    OK:
    Tester Connection
    Condition
    Specified Condition
    P6-4 (U) - P6-7 (BW)
    P6-9 (D) - Body ground
    Always
    Power window moves up
    P6-4 (U) - Body ground
    P6-7 (BW) - P6-9 (D)
    Always
    Power window moves down

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Window Regulator Master Switch Assembly)



NG
Go to step 3
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)  

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY [FOR DRIVER SIDE])
  1. Disconnect the P6 power window regulator master switch assembly connector.

  1. Disconnect the P7*1 or P8*2 front door window regulator sub-assembly (for driver side) connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    P6-9 (D) - P7-1
    Always
    Below 1 Ω
    P6-4 (U) - P7-2
    Always
    Below 1 Ω
    P6-9 (D) or P7-1 - Body ground
    Always
    10 kΩ or higher
    P6-4 (U) or P7-2 - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    P6-9 (D) - P8-1
    Always
    Below 1 Ω
    P6-4 (U) - P8-2
    Always
    Below 1 Ω
    P6-9 (D) or P8-1 - Body ground
    Always
    10 kΩ or higher
    P6-4 (U) or P8-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (FOR DRIVER SIDE) (Click here)