Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window Manual Function does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

If the front passenger side manual up/down function does not operate, a malfunction may be present in the front door window regulator sub-assembly (for front passenger side), front power window regulator switch assembly (for front passenger side), power window regulator master switch assembly or wire harness.

WIRING DIAGRAM


B276859E19


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY [FOR FRONT PASSENGER SIDE] - BATTERY)


    B276367E11
  1. Disconnect the P11 front power window regulator switch assembly (for front passenger side) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P11-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Power Window Regulator Switch Assembly [for Front Passenger Side])



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR FRONT PASSENGER SIDE)


    B280844E01
  1. Remove the front power window regulator switch assembly (for front passenger side) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (D) - 4 (SD)
    2 (U) - 3 (B)
    UP
    Below 1 Ω
    5 (D) - 4 (SD)
    2 (U) - 1 (SU)
    OFF
    Below 1 Ω
    5 (D) - 3 (B)
    2 (U) - 1 (SU)
    DOWN
    Below 1 Ω



NG
REPLACE FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR FRONT PASSENGER SIDE) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY [FOR FRONT PASSENGER SIDE] - FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY [FOR FRONT PASSENGER SIDE])
  1. Disconnect the P11 front power window regulator switch assembly (for front passenger side) connector.

  1. Disconnect the P8*1 or P7*2 front door window regulator sub-assembly (for front passenger side) connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    P11-5 (D) - P8-1
    Always
    Below 1 Ω
    P11-2 (U) - P8-2
    Always
    Below 1 Ω
    P11-5 (D) or P8-1 - Body ground
    Always
    10 kΩ or higher
    P11-2 (U) or P8-2 - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    P11-5 (D) - P7-1
    Always
    Below 1 Ω
    P11-2 (U) - P7-2
    Always
    Below 1 Ω
    P11-5 (D) or P7-1 - Body ground
    Always
    10 kΩ or higher
    P11-2 (U) or P7-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (FOR FRONT PASSENGER SIDE)


  1. Remove the front door window regulator sub-assembly (for front passenger side) (Click here).


    B290675E01


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    V100135
    Up
    V100136
    Down

  1. Apply battery voltage to connector terminals 1 and 2.

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.

  1. Check that the arm of window regulator rotates smoothly as follows.

    OK:
    for LHD 
    Measurement Condition
    Specified Condition
    Battery positive (+) → 2
    Battery negative (-) → 1
    Arm of window regulator rotates counterclockwise (Up)
    Battery positive (+) → 1
    Battery negative (-) → 2
    Arm of window regulator rotates clockwise (Down)
    for RHD 
    Measurement Condition
    Specified Condition
    Battery positive (+) → 2
    Battery negative (-) → 1
    Arm of window regulator rotates clockwise (Up)
    Battery positive (+) → 1
    Battery negative (-) → 2
    Arm of window regulator rotates counterclockwise (Down)



NG
REPLACE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (FOR FRONT PASSENGER SIDE) (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY [FOR FRONT PASSENGER SIDE])
  1. Disconnect the P6 power window regulator master switch assembly connector.

  1. Disconnect the P11 front power window regulator switch assembly (for front passenger side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P6-13 (U) - P11-1 (SU)
    Always
    Below 1 Ω
    P6-15 (D) - P11-4 (SD)
    Always
    Below 1 Ω
    P6-13 (U) or P11-1 (SU) - Body ground
    Always
    10 kΩ or higher
    P6-15 (D) or P11-4 (SD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)