POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window Manual Function does not Operate with Front Passenger Side Power Window Switch |

| 1.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY [FOR FRONT PASSENGER SIDE] - BATTERY) |
![]() |
Disconnect the P11 front power window regulator switch assembly (for front passenger side) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P11-3 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| *a | Front view of wire harness connector (to Front Power Window Regulator Switch Assembly [for Front Passenger Side]) |
|
| ||||
| OK | |
| 2.INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR FRONT PASSENGER SIDE) |
![]() |
Remove the front power window regulator switch assembly (for front passenger side) (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 5 (D) - 4 (SD) 2 (U) - 3 (B) | UP | Below 1 Ω |
| 5 (D) - 4 (SD) 2 (U) - 1 (SU) | OFF | Below 1 Ω |
| 5 (D) - 3 (B) 2 (U) - 1 (SU) | DOWN | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY [FOR FRONT PASSENGER SIDE] - FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY [FOR FRONT PASSENGER SIDE]) |
Disconnect the P11 front power window regulator switch assembly (for front passenger side) connector.
Disconnect the P8*1 or P7*2 front door window regulator sub-assembly (for front passenger side) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P11-5 (D) - P8-1 | Always | Below 1 Ω |
| P11-2 (U) - P8-2 | Always | Below 1 Ω |
| P11-5 (D) or P8-1 - Body ground | Always | 10 kΩ or higher |
| P11-2 (U) or P8-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| P11-5 (D) - P7-1 | Always | Below 1 Ω |
| P11-2 (U) - P7-2 | Always | Below 1 Ω |
| P11-5 (D) or P7-1 - Body ground | Always | 10 kΩ or higher |
| P11-2 (U) or P7-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (FOR FRONT PASSENGER SIDE) |
Remove the front door window regulator sub-assembly (for front passenger side) (Click here).

| *A | for LHD | *B | for RHD |
![]() | Up | ![]() | Down |
Apply battery voltage to connector terminals 1 and 2.
Check that the arm of window regulator rotates smoothly as follows.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 Battery negative (-) → 1 | Arm of window regulator rotates counterclockwise (Up) |
| Battery positive (+) → 1 Battery negative (-) → 2 | Arm of window regulator rotates clockwise (Down) |
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 Battery negative (-) → 1 | Arm of window regulator rotates clockwise (Up) |
| Battery positive (+) → 1 Battery negative (-) → 2 | Arm of window regulator rotates counterclockwise (Down) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY [FOR FRONT PASSENGER SIDE]) |
Disconnect the P6 power window regulator master switch assembly connector.
Disconnect the P11 front power window regulator switch assembly (for front passenger side) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P6-13 (U) - P11-1 (SU) | Always | Below 1 Ω |
| P6-15 (D) - P11-4 (SD) | Always | Below 1 Ω |
| P6-13 (U) or P11-1 (SU) - Body ground | Always | 10 kΩ or higher |
| P6-15 (D) or P11-4 (SD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||