POWER WINDOW CONTROL SYSTEM > Rear Power Window LH Manual Function does not Operate with Rear Power Window Switch LH |

| 1.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - BATTERY) |
![]() |
Disconnect the P12 rear power window regulator switch assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P12-3 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| *a | Front view of wire harness connector (to Rear Power Window Regulator Switch Assembly LH) |
|
| ||||
| OK | |
| 2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH |
![]() |
Remove the rear power window regulator switch assembly LH (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 5 (D) - 4 (SD) 2 (U) - 3 (B) | UP | Below 1 Ω |
| 5 (D) - 4 (SD) 2 (U) - 1 (SU) | OFF | Below 1 Ω |
| 5 (D) - 3 (B) 2 (U) - 1 (SU) | DOWN | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH) |
Disconnect the P12 rear power window regulator switch assembly LH connector.
Disconnect the P9 rear door window regulator sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P12-5 (D) - P9-1 | Always | Below 1 Ω |
| P12-2 (U) - P9-2 | Always | Below 1 Ω |
| P12-5 (D) or P9-1 - Body ground | Always | 10 kΩ or higher |
| P12-2 (U) or P9-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH |
![]() |
Remove the rear door window regulator sub-assembly LH (Click here)..
Apply battery voltage to connector terminals 1 and 2.
Check that the arm of window regulator rotates smoothly as follows.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 Battery negative (-) → 1 | Arm of window regulator rotates clockwise (Up) |
| Battery positive (+) → 1 Battery negative (-) → 2 | Arm of window regulator rotates counterclockwise (Down) |
![]() | Up |
![]() | Down |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH) |
Disconnect the P6 power window regulator master switch assembly connector.
Disconnect the P12 rear power window regulator switch assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P6-12 (U) - P12-1 (SU) | Always | Below 1 Ω |
| P6-10 (D) - P12-4 (SD) | Always | Below 1 Ω |
| P6-12 (U) or P12-1 (SU) - Body ground | Always | 10 kΩ or higher |
| P6-10 (D) or P12-4 (SD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||