POWER WINDOW CONTROL SYSTEM > Rear Power Window RH Manual Function does not Operate with Rear Power Window Switch RH |

| 1.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BATTERY) |
![]() |
Disconnect the P13 rear power window regulator switch assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P13-3 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| *a | Front view of wire harness connector (to Rear Power Window Regulator Switch Assembly RH) |
|
| ||||
| OK | |
| 2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH |
![]() |
Remove the rear power window regulator switch assembly RH (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 5 (D) - 4 (SD) 2 (U) - 3 (B) | UP | Below 1 Ω |
| 5 (D) - 4 (SD) 2 (U) - 1 (SU) | OFF | Below 1 Ω |
| 5 (D) - 3 (B) 2 (U) - 1 (SU) | DOWN | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY RH) |
Disconnect the P13 rear power window regulator switch assembly RH connector.
Disconnect the P10 rear door window regulator sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P13-5 (D) - P10-1 | Always | Below 1 Ω |
| P13-2 (U) - P10-2 | Always | Below 1 Ω |
| P13-5 (D) or P10-1 - Body ground | Always | 10 kΩ or higher |
| P13-2 (U) or P10-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY RH |
![]() |
Remove the rear door window regulator sub-assembly RH (Click here).
Apply battery voltage to connector terminals 1 and 2.
Check that the motor gear rotates smoothly as follows.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 Battery negative (-) → 1 | Arm of window regulator rotates counterclockwise (Up) |
| Battery positive (+) → 1 Battery negative (-) → 2 | Arm of window regulator rotates clockwise (Down) |
![]() | Up |
![]() | Down |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH) |
Disconnect the P6 power window regulator master switch assembly connector.
Disconnect the P13 rear power window regulator switch assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P6-18 (U) - P13-1 (SU) | Always | Below 1 Ω |
| P6-16 (D) - P13-4 (SD) | Always | Below 1 Ω |
| P6-18 (U) or P13-1 (SU) - Body ground | Always | 10 kΩ or higher |
| P6-16 (D) or P13-4 (SD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||