TRANSFER ASSEMBLY > DISASSEMBLY |
| 1. REMOVE TRANSFER INDICATOR SWITCH |
![]() |
Remove the indicator switches and gaskets.
| No. 1 (for Automatic Transmission) | Indicator switch (neutral position) |
| No. 2 | Indicator switch (L4 position) |
| No. 3 | Indicator switch (differential lock) |
| 2. REMOVE TRANSFER GEAR SHIFT HEAD |
![]() |
Using a pin punch and hammer, tap out the 2 slotted pins from the No. 1 and No. 2 gear shift heads.
Remove the No. 1 and No. 2 gear shift heads from the front drive shift fork shaft and the high and low shift fork shaft.
| 3. REMOVE TRANSFER BEARING RETAINER SUB-ASSEMBLY |
![]() |
Remove the 5 bolts and bearing retainer.
| 4. REMOVE TRANSFER COVER TYPE T OIL SEAL |
Using a screwdriver and hammer, tap out the oil seal from the bearing retainer.
| 5. REMOVE TRANSFER CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY (for Select Lever on Transfer) |
![]() |
Remove the 4 bolts and retainer.
| 6. REMOVE TRANSFER CASE COVER SUB-ASSEMBLY (for Select Lever on Transfer Adapter) |
![]() |
Remove the 4 bolts and case cover.
| 7. REMOVE BREATHER OIL DEFLECTOR |
| 8. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Front Side) |
Using a chisel and hammer, loosen the staked part of the lock nut.
![]() |
Using SST to hold the companion flange, remove the lock nut.
![]() |
Using SST, remove the companion flange.
| 9. REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL (for Front Side) |
Using a screwdriver and hammer, tap out the oil seal from the companion flange.
| 10. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (for Rear Side) |
Using SST, remove the lock nut and companion flange (rear) in the same way as the companion flange (front).
| 11. REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL (for Rear Side) |
Using a screwdriver and hammer, tap out the oil seal from the companion flange.
| 12. REMOVE SPEEDOMETER DRIVEN GEAR ASSEMBLY WITH VEHICLE SPEED SENSOR |
![]() |
Disconnect the connector.
Remove the bolt and speedometer driven gear assembly with vehicle speed sensor from the transfer.
| 13. REMOVE SPEEDOMETER DRIVEN GEAR SUB-ASSEMBLY |
![]() |
Remove the clip and speedometer driven gear sub-assembly from the speedometer sensor.
![]() |
Remove the O-ring from the speedometer sensor.
| 14. REMOVE TRANSFER EXTENSION HOUSING SUB-ASSEMBLY |
Remove the 5 bolts and extension housing.
| 15. REMOVE TRANSFER EXTENSION HOUSING TYPE T OIL SEAL |
Using a screwdriver and hammer, tap out the oil seal.
| 16. REMOVE TRANSFER OUTPUT SHAFT WASHER |
Remove the 2 washers and drive gear.
| 17. REMOVE REAR TRANSFER CASE |
![]() |
Remove the 12 bolts and 2 clamps.
Remove the rear case.
| 18. REMOVE NO. 2 TRANSFER GEAR SHIFT FORK WITH TRANSFER HIGH AND LOW CLUTCH SLEEVE |
![]() |
Mount the rear case in a vise.
Using a pin punch and hammer, drive out the slotted spring pin.
Using a hexagon wrench, remove the No. 1 plug.
Using a magnetic finger, remove the spring and ball from the hole.
Remove the No. 2 gear shift fork and high and low shift fork shaft.
Using a magnetic finger, remove the straight pin.
Automatic transmission:
Remove the high and low clutch sleeve.
Manual transmission:
Remove the high and low clutch sleeve, 3 shifting keys and 2 No. 1 springs.
| 19. REMOVE CENTER DIFFERENTIAL LOCK FORK SUB-ASSEMBLY WITH FRONT DRIVE CLUTCH SLEEVE |
![]() |
Mount the rear case in a vise.
Using a pin punch and hammer, drive out the slotted spring pin.
Using 2 screwdrivers and hammer, tap out the snap ring.
Using a hexagon wrench, remove the No. 2 plug.
Using a magnetic finger, remove the spring and ball from the hole.
Remove the center differential lock fork, shift shaft stopper, 2 springs, 3 stoppers, front drive shift shaft and front drive clutch sleeve.
| 20. REMOVE REAR TRANSFER OUTPUT SHAFT, FRONT DRIVE CHAIN AND DRIVEN SPROCKET SUB-ASSEMBLY |
![]() |
Mount the rear case in a vise.
Using a snap ring expander, remove the snap ring.
![]() |
Using a plastic-faced hammer, carefully tap the rear case, and remove the output shaft together with the front drive chain and driven sprocket.
Remove the output shaft and driven sprocket from the front drive chain.
| 21. REMOVE TRANSFER DRIVEN SPROCKET BEARING |
![]() |
Using a press, press out the bearing.
| 22. REMOVE TRANSFER INPUT GEAR RADIAL BALL BEARING |
![]() |
Using SST, a press and steel bar, press out the bearing.
| 23. REMOVE NO. 1 TRANSFER CASE PLUG |
Remove the filler plug (for filler) and gasket.
| 24. REMOVE NO. 1 TRANSFER CASE PLUG |
Remove the drain plug (for drain) and gasket.
| 25. REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY |
![]() |
Remove the 3 bolts and separator.
| 26. REMOVE TRANSFER CASE MAGNET |
| 27. REMOVE TRANSFER OIL PUMP BODY SUB-ASSEMBLY |
![]() |
Remove the 3 bolts and pump body.
| 28. REMOVE TRANSFER OIL PUMP BODY O-RING |
![]() |
Using a screwdriver, remove the O-ring from the pump body.
| 29. REMOVE TRANSFER OIL PUMP GEAR |
![]() |
Remove the nut and pump gear.
| 30. REMOVE TRANSFER LOW PLANETARY GEAR ASSEMBLY WITH TRANSFER INPUT SHAFT |
![]() |
Using a snap ring expander, remove the snap ring.
![]() |
Remove the low planetary gear with the input shaft.
| 31. REMOVE TRANSFER FRONT DRIVE CLUTCH SYNCHRONIZER RING (for Manual Transmission) |
| 32. REMOVE OUTPUT SHAFT SPACER |
![]() |
| 33. REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING |
| 34. REMOVE TRANSFER CASE OIL SEAL |
Using a screwdriver and hammer, tap out the oil seal (No. 1).
Using a screwdriver and hammer, tap out the oil seal (No. 2).
| 35. REMOVE TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING |
![]() |
Using a snap ring expander, pry out the snap ring.
| 36. REMOVE TRANSFER INPUT GEAR STOPPER |
![]() |
| 37. REMOVE TRANSFER INPUT GEAR STOPPER BALL |
| 38. REMOVE MANUAL TRANSFER PLANETARY CARRIER WASHER |
| 39. REMOVE TRANSFER INPUT SHAFT |
![]() |
| 40. REMOVE NO. 1 TRANSFER THRUST BEARING RACE |
| 41. REMOVE TRANSFER LOW PLANETARY GEAR BEARING |
| 42. REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING |
![]() |
Remove the 2 seal rings.
| 43. REMOVE TRANSFER INPUT SHAFT BEARING |
![]() |
Using a snap ring expander, remove the snap ring.
Using SST and a press, press out the bearing.
| 44. REMOVE TRANSFER LOW PLANETARY GEAR SPLINE PIECE |
![]() |
Using a screwdriver, remove the snap ring.
Remove the spline piece.
| 45. REMOVE TRANSFER LOW PLANETARY GEAR BEARING |
![]() |
Using SST, remove the bearing.
| 46. REMOVE TRANSFER LOW PLANETARY RING GEAR HOLE SNAP RING |
![]() |
Using a snap ring expander, remove the snap ring.
| 47. REMOVE NO. 2 TRANSFER OUTPUT SHAFT SPACER |
| 48. REMOVE TRANSFER OUTPUT SHAFT SPACER BALL |
| 49. REMOVE CENTER DIFFERENTIAL CASE |
| 50. REMOVE TRANSFER CLUTCH HUB |
![]() |
| 51. REMOVE FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING |
| 52. REMOVE TRANSFER OUTPUT SHAFT PLATE WASHER |
| 53. REMOVE REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING |
![]() |
Using SST and a press, press out the bearing.
| 54. REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER |
![]() |
| 55. REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY |
| 56. REMOVE TRANSFER DRIVE SPROCKET BEARING |
| 57. REMOVE TRANSFER OUTPUT SHAFT PLATE WASHER |
| 58. REMOVE TRANSFER CASE PLUG |
![]() |
| 59. REMOVE COMPRESSION SPRING |
| 60. REMOVE TRANSFER CASE STRAIGHT PIN |
| 61. REMOVE TRANSFER LOW PLANETARY RING GEAR |
![]() |
Using a screwdriver, pry out the snap ring.
Remove the ring gear from the front case.