Home › BRAKE › BRAKE › REAR BRAKE

REAR BRAKE > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. INSTALL REAR WHEEL BRAKE CYLINDER CUP


    C115340E02
  1. Apply lithium soap base glycol grease to 2 new cups and the 2 pistons.

  1. Install the 2 cups to the 2 pistons.

  1. Install the compression spring and 2 pistons to the cylinder.

  1. Install 2 new cylinder dust boots to the cylinder.



2. TEMPORARILY INSTALL REAR BRAKE DRUM BLEEDER PLUG
  1. Temporarily install the bleeder plug to the cylinder.

    HINT:
    The bleeder plug will be tightened to a torque specification in the "BLEED AIR FROM BRAKE LINE" procedures.

  1. Install the cap to the bleeder plug.



3. INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY LH


    C111505
  1. Install the cylinder with the 2 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 8 ft.*lbf }

  1. Using a union nut wrench, connect the brake line.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



4. APPLY HIGH TEMPERATURE GREASE


    C111506E02
  1. Apply high temperature grease to the surface of the backing plate where the shoe will be attached.

  1. Apply high temperature grease to the anchor block plate and cable setting area.



5. INSTALL REAR BRAKE PARKING BRAKE SHOE LEVER SUB-ASSEMBLY


    C111507
  1. Using needle-nose pliers, install the lever with a new C-washer.



6. INSTALL BRAKE SHOES


    C111502
  1. Using needle-nose pliers, connect the No. 3 parking brake cable to the parking brake shoe lever.

  1. Install the strut set and return spring to the shoe.



    C123253
  1. Attach the support clip to the exposed threads of the strut set.

    NOTICE:
    The support clip should not contact the adjuster nut.

  1. Using needle-nose pliers, hook the support clip around the spring.

    NOTICE:
    Be careful not to damage the spring.

  1. Install the front and rear brake shoes.



    C123256
  1. Move one of the shoes upward and install the shoe tension spring.



    C123244
  1. Install the shoe front or rear side to the cylinder. Then install the other side of the shoe to the other side of the cylinder.

    HINT:
    After one side of the shoe is installed to the cylinder, hold that side of the shoe steady. Then widen the opening of the shoe by pulling the other side of the shoe outward and install it to the other side of the cylinder.

    NOTICE:
    Be careful not to damage the cylinder dust boot.



    C111498
  1. Using pliers, install the front brake shoe, rear brake shoe, pins and shoe hold down springs.



7. INSTALL REAR BRAKE AUTOMATIC ADJUST LEVER LH


    C111497
  1. Using needle-nose pliers, install the lever and lever tension spring.



8. CHECK REAR BRAKE DRUM INSTALLATION


  1. Check that each part is installed properly.


    C123246E02



    C111600
  1. Measure the inside diameter of the drum and the diameter of the shoes. Check that the difference between the diameters is the standard shoe clearance.

    Standard shoe clearance:
    0.6 mm (0.0236 in.)

    NOTICE:
    There should be no oil or grease on the contact surfaces of the shoe lining and drum.



9. INSTALL REAR BRAKE DRUM AND NEW GASKET


10. FILL RESERVOIR WITH BRAKE FLUID (w/o VSC)

Fluid:
SAE J1704 or FMVSS No. 116 DOT 4



11. FILL RESERVOIR WITH BRAKE FLUID (w/ VSC)

Fluid:
SAE J1704 or FMVSS No. 116 DOT4



12. BLEED AIR FROM BRAKE MASTER CYLINDER (w/o VSC)

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.



    C145678
  1. Slowly depress and hold the brake pedal.



    C145679
  1. Cover the outer holes with your fingers, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake lines to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



13. BLEED AIR FROM BRAKE MASTER CYLINDER (w/ VSC)

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.



    C236931
  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.

  1. Slowly depress and hold the brake pedal.



    C236932
  1. Cover the outer holes with your fingers, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake lines to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



14. BLEED AIR FROM BRAKE LINE (w/o VSC)


C117797
  1. Remove the bleeder plug cap.

  1. Connect a vinyl tube to the bleeder plugs.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf } for front brake
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for rear brake

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.



15. BLEED AIR FROM BRAKE LINE (w/ VSC)
  1. Remove the bleeder plug cap.

  1. Connect a vinyl tube to the bleeder plugs.

  1. Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    for front brake:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    for rear brake:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the cap.



    C191545
  1. Bleed air from the brake line for each wheel by repeating the above procedures.



16. BLEED AIR FROM CLUTCH LINE (for Manual Transmission)
  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the clutch line.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

  1. Remove the bleeder plug cap.



    C147156
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.

  1. Repeat the previous 2 steps until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.

  1. Check that all the air has been bled out of the clutch line.

  1. Check for brake fluid leaks.

  1. Check the brake fluid level in the reservoir.

    1. w/ VSC:

    2. w/o VSC:

  1. Install the brake master cylinder reservoir filler cap assembly.



17. CHECK BRAKE FLUID LEVEL IN RESERVOIR (w/o VSC)


F052092
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT 4

    HINT:
    Add fluid to a level between the reservoir's MIN and MAX lines.



18. CHECK BRAKE FLUID LEVEL IN RESERVOIR (w/ VSC)


    C190487
  1. Check the fluid level.
    If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT4



19. CHECK FOR BRAKE FLUID LEAKAGE


20. INSTALL REAR WHEEL

Torque:
105 N*m{ 1,071 kgf*cm , 77 ft.*lbf }



21. CHECK PARKING BRAKE LEVER TRAVEL
  1. Pull the lever upward with a force of approximately 200 N (20 kgf, 45 lbf) and count the number of clicks.

    OK:
    7 to 9 clicks (without rear brake dragging)



22. ADJUST PARKING BRAKE LEVER TRAVEL


C112487E01
  1. Turn the No. 1 wire adjusting nut until the lever travel is correct.

    OK:
    7 to 9 clicks (without rear brake dragging)
    <Lever pulling force: approximately 200 N (20 kgf, 45 lbf)>

  1. Tighten the lock nut.

    Torque:
    5.2 N*m{ 53 kgf*cm , 46 in.*lbf }

    HINT:
    If further adjustment is necessary, proceed to the next step.