Home › ENGINE ยท 2TR-FE › COOLING › RADIATOR

RADIATOR > REASSEMBLY

for Preparation Click here



1. INSTALL OIL COOLER ASSEMBLY


    A099962E01
  1. Install 2 new O-rings to the oil cooler assembly.

  1. Install the oil cooler assembly and 2 plate washers to the radiator tank lower with the 2 nuts.

    Torque:
    8.3 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Install the 2 cooler pipes.

    Torque:
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }

    HINT:
    Set the cooler pipe labeled A to the location and angle shown in the illustration.



2. INSPECT LOCK PLATE FOR DAMAGE


    A099690E04
  1. Inspect the lock plate for damage.
    Text in Illustration 
    *1
    Lock Plate
    *2
    Core
    If the sides of the lock plate groove are deformed, reassembly of the tank will be impossible. Correct any deformations with pliers.
    Coolant will leak if the bottom of the lock plate groove is damaged or dented. Repair or replace it if necessary.

    NOTICE:
    The radiator can only be recaulked twice. After the second time, the core must be replaced.



3. INSTALL RADIATOR TANK UPPER AND RADIATOR TANK LOWER


    A252179E01
  1. Check that there are no foreign objects in the lock plate groove, and install 2 new O-ring. Make sure each O-ring is not twisted.
    Text in Illustration 
    *1
    O-Ring
    *a
    CORRECT
    *b
    INCORRECT
    *c
    Normal
    *d
    Twisted

    HINT:
    When cleaning the lock plate groove, lightly rub it with sandpaper without scratching it.

  1. Install the tank without damaging the O-ring.



    A113342E02
  1. Tap the lock plate with a plastic-faced hammer so that there is no gap between the lock plate and the tank.
    Text in Illustration 
    *1
    Tank
    *2
    Lock Plate
    *a
    CORRECT
    *b
    INCORRECT



4. ASSEMBLE SST


    A234961E03
  1. Install the punch assembly to part A of the overhaul handle as shown in the illustration.

    SST
    09230-01010   (09231-01010, 09231-01020)
    09231-14010  
    Text in Illustration 
    *1
    Part A
    *2
    Stopper Bolt
    *a
    Dimension B

  1. While gripping the handle, adjust the stopper bolt so that dimension B is as specified below.

    Dimension B:
    8.4 mm (0.331 in.)



5. CAULK LOCK PLATE


    A099703E03
  1. Lightly press SST against the lock plate in the order shown in the illustration. Repeat this step a few times, and then fully caulk the lock plate by squeezing the handle until stopped by the stopper bolt.

    SST
    09230-01010   (09231-01010, 09231-01020)
    09231-14010  
    Text in Illustration 
    *1
    Stopper Bolt
    *2
    Tank
    *3
    Lock Plate

    NOTICE:

    1. A120272E01
      Do not press the protruding areas around the ports (1) and bracket (2).

    2. A099705E01
      Do not use SST to press the areas indicated by the circle marks in the illustration. Use pliers and be careful not to damage the core plates.



    A099706E03
  1. Check the lock plate height after completing the caulking.

    Standard plate height:
    8.8 mm (0.346 in.)

    Text in Illustration 
    *1
    Lock Plate Height
    If the height is not as specified, readjust the stopper bolt of the handle and caulk the lock plate again.



6. INSTALL RADIATOR DRAIN COCK PLUG
  1. Install a new O-ring to the radiator drain cock plug.

  1. Install the radiator drain cock plug.



7. INSPECT FOR WATER LEAKS


    A099707E01
  1. Plug the inlet and outlet pipes of the radiator assembly with SST.

    SST
    09230-01010   (09231-00030, 09231-00060)

  1. Using a radiator cap tester, apply pressure to the radiator assembly.

    Standard test pressure:
    177 kPa (1.8 kgf/cm2, 26 psi)

  1. Submerge the radiator assembly in water.



    A090282E04
  1. Inspect for leaks.
    Text in Illustration 
    *1
    Tank
    *2
    Lock Plate
    *3
    O-Ring

    HINT:
    For radiators with resin tanks, there is clearance between the tank and lock plate where a small amount of air will remain. This air is released when the radiator is submerged in water, giving the appearance of an air leak. Before performing the water leak test, first shake the radiator in the water until all air bubbles are released.



8. INSTALL RADIATOR SIDE PLATE LH
  1. Install the radiator side plate LH with the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



9. INSTALL RADIATOR SIDE PLATE RH
  1. Install the radiator side plate RH with the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }