2KD-FTV STARTING > SERVICE DATA |
| Standard resistance | Tester connection | Condition | Specified Condition |
| Glow plug terminal - Body ground | 20°C (68°F) | Approx. 0.95 Ω |
| Starter | No-load characteristics current | 123 A or less at 11.5 V | |
| Starter armature assembly | Standard circle runout | 0.02 mm (0.000787 in.) | |
| Maximum circle runout | 0.04 mm (0.00157 in.) | ||
| Standard commutator diameter | 32.2 mm (1.27 in.) | ||
| Minimum commutator diameter | 31.1 mm (1.22 in.) | ||
| Standard undercut depth | 0.9 mm (0.0354 in.) | ||
| Minimum undercut depth | 0.4 mm (0.0157 in.) | ||
| Brush | Standard length | 14.0 mm (0.551 in.) | |
| Minimum length | 9.0 mm (0.354 in.) | ||
| Starter armature assembly | Standard resistance | Segments | Below 1.7 Ω |
| Segment - Armature coil core | 10 kΩ or higher | ||
| Brush | Standard resistance | Tester connection A-B | 10 kΩ or higher |
| Tester connection A-C | 10 kΩ or higher | ||
| Tester connection A-D | Below 1 Ω | ||
| Tester connection B-C | Below 1 Ω | ||
| Tester connection B-D | 10 kΩ or higher | ||
| Tester connection C-D | 10 kΩ or higher | ||
| Magnet starter switch assembly | Standard resistance | Terminal 50 - Terminal C | Below 1 Ω |
| Terminal 50 - Starter magnet switch body | Below 2 Ω | ||
| Starter | No-load characteristics current | 180 A or less at 11 V | |
| Starter armature assembly | Maximum circle runout | 0.05 mm (0.00197 in.) | |
| Standard commutator diameter | 36.0 mm (1.42 in.) | ||
| Minimum commutator diameter | 35.0 mm (1.38 in.) | ||
| Standard undercut depth | 0.7 mm (0.0276 in.) | ||
| Minimum undercut depth | 0.2 mm (0.00787 in.) | ||
| Brush | Standard length | 20.5 mm (0.814 in.) | |
| Minimum length | 11.0 mm (0.433 in.) | ||
| Brush spring | Standard spring load | 26 to 45 N (3 to 5 kgf, 5.8 to 10.1 lbf) | |
| Minimum spring load | 12 N (1 kgf, 2.8 lbf) | ||
| Starter armature assembly | Standard resistance | Segments | Below 1 Ω |
| Segment - Armature coil core | 10 kΩ or higher | ||
| Brush | Standard resistance | Lead wire - brush | Below 1 Ω |
| Starter yoke body - brush | 10 kΩ or higher | ||
| Starter brush holder assembly | Standard resistance | Positive (+) brush holder - Negative (-) brush holder | 10 kΩ or higher |
| Starter magnet switch assembly | Standard resistance | Terminal 50 - Terminal C | Below 1 Ω |
| Terminal 50 - Starter magnet switch body | Below 2 Ω | ||
| Standard resistance | Tester connection | Specified Condition |
| 3-5 | 10 kΩ or higher | |
| Below 1 Ω (when battery voltage is applied to terminal 1 and 2) |
| Standard resistance | Tester connection | Specified Condition |
| 3-5 | 10 kΩ or higher | |
| Below 1 Ω (when battery voltage is applied to terminal 1 and 2) |
| Standard resistance | Tester connection | Switch condition | Specified condition |
| - | Lock | 10 kΩ or higher | |
| 2 (ACC) - 4 (AM1) | ACC | Below 1 Ω | |
| 1 (IG1) - 4 (AM1) 2 (ACC) - 4 (AM1) 5 (AM2) - 6 (IG2) | ON | Below 1 Ω | |
| 1 (IG1) - 4 (AM1) 3 (ST1) - 4 (AM1) 5 (AM2) - 6 (IG2) 5 (AM2) - 7 (ST2) | START | Below 1 Ω |