DIFFERENTIAL SYSTEM (w/ Differential Lock) > ON-VEHICLE INSPECTION |
| 1. CHECK DIFFERENTIAL LOCK SYSTEM |
![]() |
Check the indicator light.
Check that the indicator lights up for approx. 1 second when the ignition switch is turned ON.
Check the differential lock operation.
Jack up the vehicle and start the engine.
Shift the transfer shift lever to the L position.
When the differential lock control switch is set to the ON position, the indicator light turns on. Differential lock is applied to the rear wheel at this time.
When the differential lock control switch is at the OFF position, the indicator light goes off. Differential lock is released for the rear wheel at this time.
![]() |
Measure the voltage between the terminals of the four wheel drive control ECU when switching the differential control switch with the speedometer registering approx. 8 km/h (5 mph) or more.
| Switch Condition | Tester Connection | Specified value |
| ON | 3 (M1) - 2 (M2) | 0.5 V or less (No change) |
Return the differential lock control switch to OFF.
Stop the engine and lower the vehicle.
| 2. CHECK WIRE HARNESS |
![]() |
Check the system circuit with the connector disconnected.
Disconnect the F18 connector from the four wheel drive control ECU.
| Tester Connection | Trouble Part | Condition | Specified Condition |
| 3 (M1) - 2 (M2) | Differential lock shift actuator | - | Below 100 Ω |
| 7 (GND) - Body ground | Body ground | - | Below 1 Ω |
| 10 (SPD) - Body ground | Speed sensor | Vehicle moves slowly | 1 pulse 40 cm (15.75 in.) |
| 5 (IG) - Body ground | Differential fuse | Ignition switch ON | 0 to 14 V |
| 1 (RLP) - Body ground | Rear differential lock indicator switch | Ignition switch ON with indicator light ON | About 0 V |
| Ignition switch ON with indicator light OFF | 0 to 14 V | ||
| 8 (4WD) - Body ground | L position switch | Ignition switch ON with transfer shift lever not on L | About 0 V |
| Ignition switch ON with transfer shift lever on L | 0 to 14 V | ||
| 4 (R) - Body ground | Differential lock control switch | Ignition switch ON with differential lock control switch ON | 0 to 14 V |
| Ignition switch ON with differential lock control switch OFF | About 0 V |
Measure the resistance of the wire harness side connector.
| Tester Connection | Trouble Part | Condition | Specified Condition |
| 3 (M1) - 2 (M2) | Differential lock shift actuator | - | Below 100 Ω |
| 7 (GND) - Body ground | Body ground | - | Below 1 Ω |
Measure the voltage of the wire harness side connector.
| Tester Connection | Trouble Part | Condition | Specified Condition |
| 1 (RLP) - Body ground | Rear differential lock indicator switch | Ignition switch ON with indicator light ON | About 0 V |
| Ignition switch ON with indicator light OFF | 0 to 14 V | ||
| 8 (4WD) - Body ground | L position switch | Ignition switch ON with transfer shift lever not on L | About 0 V |
| Ignition switch ON with transfer shift lever on L | 0 to 14 V | ||
| 4 (R) - Body ground | Differential lock control switch | Ignition switch ON with differential lock control switch ON | 0 to 14 V |
| Ignition switch ON with differential lock control switch OFF | About 0 V |
| 3. CHECK FOUR WHEEL DRIVE CONTROL ECU |
![]() |
Check the system circuit with the connector connected.
Turn the ignition switch to the ON position.
Shift the transfer shift lever to the L position.
Measure the voltage when the control switch is in the position shown in the table.
| Tester Connection | Switch Position | Specified Condition |
| 8 (4WD) - 7 (GND) | - | 0.5 V or less |
| (RLP) - 7 (GND) | ON*
| 0.5 V or less |
| 3 (M1) - 2 (M2) | OFF → ON | 0.5 V or less → 10 to 14 V (approx. 1 sec.) →0.5 V or less |
| 2 (M2) - 3 (M1) | ON → OFF |
| 4. CHECK DIFFERENTIAL LOCK SHIFT ACTUATOR |
Jack up the vehicle.
Use a heater relay (marking: HTR) and connect it, as shown below.
Rotate the tire and check that the actuator changes from free to lock and lock to free.
