Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0047    Turbocharger/Supercharger Boost Control "A" Circuit Low

DTC    P0048    Turbocharger/Supercharger Boost Control "A" Circuit High

for Preparation Click here


DESCRIPTION

Refer to DTC P0046 .

DTC No.
DTC Detection Condition
Trouble Area
P0047
All of following conditions met for 1 second or more
(1 trip detection logic):
  1. DC motor duty ratio 100%
  2. DC motor current 0.5 A or less
  1. Open in DC motor circuit
  2. Turbo motor driver
  3. DC Motor (Turbocharger sub-assembly)
P0048
DC motor current 6.5 A or more for 0.5 seconds or more
(1 trip detection logic)
  1. Short in DC motor circuit
  2. Turbo motor driver
  3. DC Motor (Turbocharger sub-assembly)

WIRING DIAGRAM

Refer to DTC P0046 .

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)
  1. Turn the ignition switch ON.

  1. Turn the ignition switch OFF and check the DC motor operation.

    OK:
    When ignition switch is turned OFF, operation link moves as shown in A to D in illustration below.


A158317E01



OK
CHECK FOR INTERMITTENT PROBLEMS (Click here)
NG


2.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR)


    G036521E03
  1. Disconnect the T10 DC motor connector.

  1. Measure the resistance of the DC motor.

    Standard resistance:
    Tester Connection
    Specified Condition
    2 (M+) - 1 (M-)
    1 to 100 Ω



NG
REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER)


    A150170E12
  1. Disconnect the T10 DC motor connector.

  1. Disconnect the T34 turbo motor drive connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    T34-12 (M+) - T10-2 (M+)
    Below 1 Ω
    T34-5 (M-) - T10-1 (M-)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    T34-12 (M+) or T10-2 (M+) - Body ground
    10 kΩ or higher
    T34-5 (M-) or T10-1 (M-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE TURBO MOTOR DRIVER

NEXT


5.CHECK IF DTC OUTPUT RECURS (DTC P0047 AND/OR P0048)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Perform the test drive.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0047 and/or P0048
    A
    No output
    B



B
END
A

REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)