DTC P2563 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Range/Performance |
DTC P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low |
DTC P2565 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High |
DTC P2588 Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit Low |
DTC P2589 Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit High |

| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 1 seconds | Difference between VTA1 and VTA2 voltage 0.8 V or more for 0.5 seconds or more (1 trip detection logic) | Nozzle vane position sensor (Turbocharger sub-assembly) |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 1 seconds | VTA1 voltage 0.5 V or less for 0.5 seconds or more (1 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 1 seconds | VTA1 voltage 4.5 V or more for 0.5 seconds or more (1 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 1 seconds | VTA2 voltage 0.5 V or less for 0.5 seconds or more (1 trip detection logic) |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 1 seconds | VTA2 voltage 4.5 V or more for 0.5 seconds or more (1 trip detection logic) |
|

| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2563, P2564, P2565, P2588 AND/OR P2589) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P2563, P2564, P2565, P2588 and/or P2589 is output | A |
| P2563, P2564, P2565, P2588 and/or P2589 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (NOZZLE VANE POSITION SENSOR - TURBO MOTOR DRIVER) |
Disconnect the nozzle vane position sensor connector.
Disconnect the turbo motor driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T11-1 (VTA1) - T34-9 (VTA1) | Always | Below 1 Ω |
| T11-2 (VNE2) - T34-8 (VNE2) | Always | Below 1 Ω |
| T11-3 (VNVC) - T34-1 (VNVC) | Always | Below 1 Ω |
| T11-4 (VTA2) - T34-10 (VTA2) | Always | Below 1 Ω |
| T11-5 (E2S) - T34-11 (E2S) | Always | Below 1 Ω |
| T11-6 (VCS) - T34-6 (VCS) | Always | Below 1 Ω |
| T11-1 (VTA1) or T34-9 (VTA1) - Body ground | Always | 10 kΩ or higher |
| T11-2 (VNE2) or T34-8 (VNE2) - Body ground | Always | 10 kΩ or higher |
| T11-3 (VNVC) or T34-1 (VNVC) - Body ground | Always | 10 kΩ or higher |
| T11-4 (VTA2) or T34-10 (VTA2) - Body ground | Always | 10 kΩ or higher |
| T11-5 (E2S) or T34-11 (E2S) - Body ground | Always | 10 kΩ or higher |
| T11-6 (VCS) or T34-6 (VCS) - Body ground | Always | 10 kΩ or higher |
Reconnect the turbo motor driver connector.
Reconnect the nozzle vane position sensor connector.
|
| ||||
| OK | |
| 3.CHECK TURBO MOTOR DRIVER (SENSOR POWER SOURCE) |
![]() |
Disconnect the nozzle vane position sensor connector.
Turn the ignition switch to ON.
Measure the voltage between the terminals of the nozzle vane position sensor connector.
| Tester Connection | Switch Condition | Specified Condition |
| T11-3 (VNVC) - T11-2 (VNE2) | Ignition switch ON | 4.5 to 5.5 V |
| T11-6 (VCS) - T11-5 (E2S) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of with harness connector (to Nozzle Vane Position Sensor) |
Reconnect the nozzle vane position sensor connector.
|
| ||||
| OK | |
| 4.INSPECT TURBO MOTOR DRIVER (VTA1, VTA2 VOLTAGE) |
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| T34-9 (VTA1) - T34-8 (VNE2) | Ignition switch ON | 0.5 to 4.5 V |
| T34-10 (VTA2) - T34-11 (E2S) | Ignition switch ON | 0.5 to 4.5 V |
| *a | Component with harness connected (Turbo Motor Driver) |
Check the difference between the voltage values.
|
| ||||
| OK | |
| 5.REPLACE TURBO MOTOR DRIVER |
Replace turbo motor driver .
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2563, P2564, P2565, P2588 AND/OR P2589) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P2563, P2564, P2565, P2588 and/or P2589 output again | A |
| No DTC is output | B |
|
| ||||
| A | |
| 7.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR) |
Replace turbocharger sub-assembly (Click here).
|
| ||||
| 8.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (Click here).
Turn the ignition switch off.
Remove the EFI fuse from the engine room relay block and junction block assembly for more than 1 minute.
Turn the ignition switch to ON and wait for 10 seconds or more.
Start the engine.
Drive the vehicle with a city driving pattern at least 10 minutes.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||