EGR VALVE > INSTALLATION |
| 1. TEMPORARILY INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY |
Place a new gasket, the electric EGR control valve, another new gasket and the intake air connector onto the stud bolts of the No. 2 intake air connector and temporarily install the 3 nuts labeled A in the illustration.
Install a new gasket and the EGR valve adapter to the electric EGR control valve with the 2 bolts labeled B in the illustration.
Set a new gasket on the intake manifold.
Temporarily install the intake air connector to the intake manifold with the 3 bolts labeled C in the illustration.

| *1 | No. 2 Intake Air Connector | *2 | Electric EGR Control Valve |
| *3 | Intake Air Connector | *4 | EGR Valve Adapter |
| *5 | New Gasket | *6 | Claw |
| *7 | Intake Manifold | - | - |
| *a | 0 to 2 threads | - | - |
| 2. INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY |
Temporarily install the No. 1 EGR pipe and 2 new gaskets to the cylinder head and EGR valve adapter with the 2 nuts and 2 bolts.
Tighten the 2 bolts labeled A.
Tighten the 2 nuts labeled B.

| *1 | New Gasket | *2 | Claw |
| 3. TIGHTEN INTAKE AIR CONNECTOR |
Tighten the 3 nuts labeled A in the illustration.
Tighten the 3 bolts labeled B in the illustration.

| *a | Front Side of Vehicle | - | - |
| 4. INSTALL NO. 2 INTAKE AIR CONNECTOR BRACKET |
![]() |
Temporarily install the No. 2 intake air connector bracket with the 3 bolts.
Tighten the bolt labeled A.
Tighten the 2 bolts labeled B.
| 5. INSTALL ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (for EGR) |
Install the electric vacuum regulating valve bracket with the 2 bolts.
Install the No. 1 gas filter with gas filter bracket with the bolt.
Connect the 6 vacuum hoses.
Connect the 2 connectors.
| 6. CONNECT NO. 3 WATER BY-PASS PIPE |
Connect the No. 3 water by-pass pipe with wire harness with the 2 bolts.
| 7. INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY |
Temporarily install the No. 1, No. 2 and No. 3 injection pipes with the union nuts.
![]() |
Install the No. 2 and No. 3 injection pipe clamps with the 2 bolts and 2 nuts as shown in the illustration.
| *1 | No. 2 Injection Pipe |
| *2 | Painted Mark |
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 8. INSTALL DIESEL THROTTLE BODY ASSEMBLY |
| 9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 10. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Check if the engine starts.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2
| *a | Reference (Active Test Operation) |
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| 11. INSPECT FOR FUEL LEAK |
Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.
Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.
Disconnect the return hose from the common rail.
Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.
Connect the intelligent tester to the DLC3.
Start the engine and push the intelligent tester main switch on.
Select the Fuel Leak test from the Active Test mode on the intelligent tester.
If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.
Check that there are no leaks from any part of the fuel system.
Reconnect the return hose to the common rail.