Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

DTC    B279A    Theft Deterrent System Communication Line High Fixation

for Preparation Click here


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck on HI output, the ECM stores this DTC.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B279A
The communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck on HI output (1 trip detection logic*).
  1. Harness or connector
  2. Transponder key ECU assembly
  3. ECM
Turn the ignition switch to ON and wait 6 seconds.
  1. *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stop).
Engine cannot be started.

Related Data List and Active Test 
DTC Code
Data List and Active Test
B279A
-

WIRING DIAGRAM


B294223E02


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the transponder key ECU assembly or ECM, refer to the Service Bulletin.
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
After troubleshooting for this DTC, make sure B279A is not present. If present, troubleshoot the blocking system DTCs next.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC B279A and other DTCs are output
    B
    DTC B279A is output
    C

    HINT:
    If any DTCs other than B279A are output, troubleshoot those DTCs first.



B
Go to DIAGNOSTIC TROUBLE CODE CHART (Click here)

C
Go to step 3
A

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK HARNESS AND CONNECTOR (SFI OR ECD COMMUNICATION LINE)
  1. Disconnect the T21 transponder key ECU assembly connector.

  1. Disconnect the E5 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) - E5-30 (IMI)
    Always
    Below 1 Ω
    T21-13 (EFIO) or E5-30 (IMI) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T21-13 (EFIO) or E5-30 (IMI) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)


    B274402E03
  1. Using an oscilloscope, check the waveform.
    Measurement Condition 
    Item
    Content
    Tester Connection
    T21-13 (EFIO) - T21-16 (GND)
    Tool Setting
    10V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON

    HINT:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

OK:
Waveform is output normally (refer to illustration).

Text in Illustration 
*1
Waveform
*a
Component with harness connected
(Transponder Key ECU Assembly)


NG
Go to step 5
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY 

5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)


    B274403E06
  1. Disconnect the T21 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T21-16 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T21-1 (+B) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Transponder Key ECU Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE ECM
  1. Temporarily replace the ECM with a new one.

    1. for 1KD-FTV: Click here
    2. for 2KD-FTV: Click here


NEXT


7.REGISTER ECU COMMUNICATION ID
  1. Register the ECU - ECM communication ID (Refer to the Service Bulletin).


NEXT


8.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


9.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B279A is not output.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

END (ECM IS DEFECTIVE)