VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON |

| 1.CHECK FOR DTC |
Check for DTC (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
|
| ||||
| OK | |
| 3.CHECK TERMINAL VOLTAGE (IG1 TERMINAL) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S25-34 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly]) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S25-1 (GND1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK BRAKE BOOSTER ASSEMBLY |
Check the brake booster assembly (Click here).
|
| ||||
| OK | |
| 6.INSPECT BRAKE FLUID LEVEL WARNING SWITCH |
Turn the ignition switch to ON.
With the brake fluid at the specified level, disconnect the brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector and check the brake warning light.
| Result | Proceed to | |
| Brake warning light does not turn off | for 1KD-FTV and 2KD-FTV | A |
| except for 1KD-FTV and 2KD-FTV | B | |
| Brake warning light turns off | C | |
|
| ||||
|
| ||||
| A | |
| 7.CHECK VACUUM WARNING SWITCH ASSEMBLY |
Start the engine.
Idle the engine.
Disconnect the vacuum warning switch connector and check the brake warning light.
| Result | Proceed to |
| Brake warning light does not turn off | A |
| Brake warning light turns off | B |
|
| ||||
| A | |
| 8.INSPECT PARKING BRAKE SWITCH ASSEMBLY |
![]() |
Turn the ignition switch off.
Disconnect the parking brake switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Body ground | Parking brake switch ON (Switch pin free) | Below 1 Ω |
| 1 - Body ground | Parking brake switch OFF (Switch pin pushed in) | 10 kΩ or higher |
| *a | Component without harness connected (Parking Brake Switch Assembly) |
| *b | Free |
| *c | Pushed in |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER AND PARKING BRAKE SWITCH) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the C27 combination meter connector.
Disconnect the parking brake switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S25-8 (BRL) - C27-26 | Always | Below 1 Ω |
| S25-8 (BRL) - Body ground | Always | 10 kΩ or higher |
| S25-29 (PKB) - P3-1 | Always | Below 1 Ω |
| S25-29 (PKB) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BODY GROUND) |
Turn the ignition switch off.
Disconnect the C27 combination meter connector.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the brake fluid level warning switch (brake master cylinder reservoir assembly) connector.
for 1KD-FTV and 2KD-FTV:
Disconnect the vacuum warning switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C27-36 (SW) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BRAKE WARNING LIGHT) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Brake Warning Light | Brake warning light | Warning light ON / OFF | Observe the combination meter. |
When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
| Brake Warning Light | Brake warning light / ON or OFF | ON: Brake warning light on OFF: Brake warning light off | - |
| Result | Proceed to | |
| Data List Display | Data List Display When Performing Active Test ON/OFF Operation | |
| ON | Does not change between ON and OFF | A |
| Changes between ON and OFF | B | |
| OFF | Does not change between ON and OFF | A |
| Changes between ON and OFF | B | |
|
| ||||
| A | ||
| ||