FUEL TANK > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FUEL TANK CAP ASSEMBLY |
| 3. REMOVE NO. 1 FUEL TANK PROTECTOR |
![]() |
Remove the 4 nuts and No. 1 fuel tank protector.
| 4. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE |
![]() |
Disconnect the fuel tank main tube and fuel tank return tube.
| 5. DISCONNECT FUEL TANK BREATHER HOSE |
![]() |
Disconnect the fuel tank breather hose from the fuel tank filler pipe.
Detach the fuel tank breather hose from the 2 clamps.
| 6. DISCONNECT FUEL TANK TO FILLER PIPE HOSE |
Disconnect the fuel tank to filler pipe hose from the fuel tank filler pipe.
| 7. REMOVE FUEL TANK FILLER PIPE |
Remove the bolt, nut and fuel tank filler pipe.
| 8. REMOVE FUEL TANK ASSEMBLY |
Place an engine lifter under the fuel tank.
![]() |
Remove the 3 bolts, 3 clips, 3 pins and 3 fuel tank bands.
Slightly lower the engine lifter.
![]() |
Fold back approximately half of each cushion so that the wire harness can be removed in the step below.
| *1 | Fuel Tank Cushion |
| *2 | Wire Harness |
| *3 | Fuel Tank |
![]() |
Detach the wire harness from the 4 clamps shown in the illustration.
| *1 | Claw |
Disconnect the fuel sender gauge connector.
| 9. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY |
![]() |
Using needle-nose pliers, remove the 5 clips and 2 nuts shown in the illustration, and then remove the No. 1 fuel tank protector.
![]() | Clip |
![]() | Nut |
| 10. REMOVE FUEL TANK CUSHION |
![]() |
Remove the 4 fuel tank cushions from the fuel tank.
![]() | Fuel Tank Cushion |
| 11. REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY |
![]() |
Remove the No. 1 fuel evaporation tube.
| 12. REMOVE FUEL PUMP GAUGE RETAINER |
![]() |
Remove the 2 tube joint clips and pull out the 2 fuel tank tubes.
![]() |
| *1 | Fuel Tube Joint |
| *2 | Fuel Tube |
| *3 | O-Ring |
| *4 | Tube Joint Clip |
Remove the fuel tank return tube and fuel tank main tube from the fuel tank.
![]() |
Temporarily install SST (plate and 4 claws) to the fuel pump gauge retainer.
| *1 | SST (Plate) |
| *2 | SST (Claw) |
| *3 | Rib |
While pressing SST (claws) to the fuel pump gauge retainer ribs securely, install the 4 bolts.
Install SST (handle).
![]() |
Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing SST, rotate the handle slowly to loosen the fuel pump gauge retainer.
Remove the fuel pump gauge retainer.
| 13. REMOVE FUEL TANK VENT TUBE SUB-ASSEMBLY |
Remove the fuel tank vent tube from the fuel tank.
Remove the gasket from the fuel tank.
| 14. REMOVE FUEL TANK BREATHER HOSE |
![]() |
Remove the fuel tank breather hose from the fuel tank.
| 15. REMOVE FUEL TANK TO FILLER PIPE HOSE |
Remove the fuel tank to filler pipe hose from the fuel tank.