STEERING PAD SWITCH > INSPECTION |
| 1. INSPECT STEERING PAD SWITCH LH (w/o Multi-information Display) |
Measure the resistance according to the value(s) in the table below.

| *1 | Volume+ Switch | *2 | Volume- Switch |
| *3 | Seek+ Switch | *4 | Seek- Switch |
| *5 | MODE Switch | *6 | Horn Wire |
| Tester Connection | Switch Condition | Specified Condition |
| 9 (AU2) - 8 (EAU) | No switch pushed | 95 to 105 kΩ |
| 9 (AU2) - 8 (EAU) | MODE switch pushed | Below 2.5 Ω |
| 10 (AU1) - 8 (EAU) | No switch pushed | 95 to 105 kΩ |
| 10 (AU1) - 8 (EAU) | Seek+ switch pushed | Below 2.5 Ω |
| 10 (AU1) - 8 (EAU) | Seek- switch pushed | 312.6 to 345.5 Ω |
| 10 (AU1) - 8 (EAU) | Volume+ switch pushed | 950 to 1050 Ω |
| 10 (AU1) - 8 (EAU) | Volume- switch pushed | 2954.5 to 3265.5 Ω |
| 1 (HO) - Horn wire | Always | Below 2.5 Ω |
Check the illumination.
Connect the battery positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.
Check that the switch illumination comes on.
| 2. INSPECT STEERING PAD SWITCH ASSEMBLY (w/ Multi-information Display) |
Measure the resistance according to the value(s) in the table below.

| *1 | Volume+ Switch | *2 | Volume- Switch |
| *3 | Seek+ Switch | *4 | Seek- Switch |
| *5 | MODE Switch | *6 | On Hook Switch |
| *7 | Off Hook Switch | *8 | DISP Switch |
| *9 | Horn Wire | - | - |
| Tester Connection | Switch Condition | Specified Condition |
| 9 (AU2) - 8 (EAU) | No switch pushed | 95 to 105 kΩ |
| 9 (AU2) - 8 (EAU) | MODE switch pushed | Below 2.5 Ω |
| 9 (AU2) - 8 (EAU) | On hook switch pushed | 312.6 to 345.5 Ω |
| 9 (AU2) - 8 (EAU) | Off hook switch pushed | 950 to 1050 Ω |
| 10 (AU1) - 8 (EAU) | No switch pushed | 95 to 105 kΩ |
| 10 (AU1) - 8 (EAU) | Seek+ switch pushed | Below 2.5 Ω |
| 10 (AU1) - 8 (EAU) | Seek- switch pushed | 312.6 to 345.5 Ω |
| 10 (AU1) - 8 (EAU) | Volume+ switch pushed | 950 to 1050 Ω |
| 10 (AU1) - 8 (EAU) | Volume- switch pushed | 2954.5 to 3265.5 Ω |
| 7 (DISP) - 8 (EAU) | DISP switch pushed | Below 2.5 Ω |
| 1 (HO) - Horn wire | Always | Below 2.5 Ω |
Connect the battery positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.
Check that the switch illumination comes on.