Home › BODY › ENGINE HOOD / DOOR › REAR DOOR

REAR DOOR > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    B277098
  1. Using a moulding remover, detach the 2 clips and 2 claws.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



4. REMOVE DOOR PULL HANDLE


    B277099
  1. Remove the screw and door pull handle.



5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B279384
  1. Remove the screw.

  1. Detach the 10 clips and remove the rear door trim board.



6. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH


    B281276
  1. Raise the 6 claws of the rear door inner glass weatherstrip as shown in the illustration, and then remove the rear door inner glass weatherstrip from the rear door trim board.



7. REMOVE REAR DOOR OUTER GLASS WEATHERSTRIP LH


    B279385E01
  1. Put protective tape around the rear door outer glass weatherstrip.
    Text in Illustration 
    *1
    Protective Tape

  1. Detach the 4 claws and remove the rear door outer glass weatherstrip.



8. REMOVE REAR SPEAKER ASSEMBLY


    E233203E01
  1. Disconnect the connector.

  1. Put a 5 mm (0.197 in.) drill bit into a drill.

  1. Wind tape around the drill bit approximately 4 mm (0.157 in.) from the tip of the drill as shown in the illustration.

    NOTICE:
    Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going to deep.
    Standard 
    Area
    Specified Condition
    A
    4 mm (0.157 in.)

  1. Lightly press the drill against the 3 rivets, drill off the flanges of the 3 rivets and remove the front No. 1 speaker assembly.

    CAUTION:
    Be careful of the drilled rivet as it may become hot.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.

  1. Continue drilling and push out the remaining rivet fragments.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.



9. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    B279395E01
  1. Detach the claw and 2 guides as indicated by the arrows in the order shown in the illustration.



    B277028
  1. Disconnect the rear door inside locking cable and rear door lock remote control cable and remove the rear door inside handle.



10. REMOVE REAR DOOR NO. 2 TRIM BRACKET


    B277102
  1. Remove the 2 screws and rear door No. 2 trim bracket.



11. REMOVE REAR DOOR SERVICE HOLE COVER LH


    B279386
  1. Pull out the rear door inside locking cable, rear door lock remote control cable and wire harness from the rear door service hole cover, and then remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the rear door panel.



12. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
  1. Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the rear door glass so that the rear door glass channel can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Remove the rear power window regulator switch assembly with rear door armrest base panel.



    B279387
  1. Partially remove the rear door glass run as shown in the illustration.



    B279388E01
  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window division bar may fall and become damaged.

    Text in Illustration 
    *1
    Temporary Bolt

  1. Remove the screw and bolt.



    B279389
  1. Remove the rear door window division bar together with the rear door glass run as shown in the illustration.

  1. Remove the rear door window division bar from the rear door glass run.



13. REMOVE REAR DOOR GLASS RUN LH


    B279390
  1. Remove the front side of the rear door glass run.



14. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    B279393
  1. Remove the rear door quarter window glass.



15. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH


    B281277
  1. Remove the rear door quarter window weatherstrip from the rear door quarter window glass.



16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    B279394
  1. Remove the rear door glass from the rear door window regulator assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.



17. REMOVE NO. 2 BLACK OUT TAPE LH

HINT:
When removing the No. 2 black out tape, heat the vehicle body and No. 2 black out tape using a heat light.

Standard:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
No. 2 Black Out Tape
40 to 60°C (104 to 140°F)

NOTICE:
Do not heat the vehicle body or No. 2 black out tape excessively.



    B279391
  1. Pull back an edge of the No. 2 black out tape and pull it parallel to the vehicle body to remove it.



18. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH


    B281278E01
  1. Using a screwdriver, remove the rear door glass channel.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape



19. REMOVE REAR DOOR GLASS CHANNEL FILLER


    B278822
  1. Remove the rear door glass channel filler.



20. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
  1. Disconnect the connector.



    B281320E01
  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and become damaged.

    Text in Illustration 
    *1
    Temporary Bolt

  1. Remove the 3 bolts and rear door window regulator.

  1. Remove the temporary bolt from the rear door window regulator.



21. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    B288570
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.



22. REMOVE REAR DOOR OUTSIDE MOULDING LH
  1. Put a 4 mm (0.157 in.) drill bit into a drill.



    B279908E01
  1. Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

    NOTICE:
    Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    Standard:
    Area
    Specified Condition
    A
    5 mm (0.197 in.)

  1. Lightly press the drill against the 3 rivets and drill off the flanges of the 3 rivets.

    CAUTION:
    Be careful of the drilled rivet as it may become hot.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.



    B279909E01
  1. Put protective tape around the rear door outside moulding.
    Text in Illustration 
    *1
    Protective Tape

  1. Detach the 5 clips and remove the rear door outside moulding.

  1. Remove the 5 clips from the vehicle body.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.



23. REMOVE REAR DOOR LOCK ASSEMBLY LH


    B291228
  1. Disconnect the connector.

  1. Disconnect the rear door inside locking cable and rear door lock remote control cable from the clamps.

  1. Using a T30 "TORX" socket wrench, remove the 3 screws and rear door lock.



24. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B281141
  1. Remove the rear door lock remote control cable.



25. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B281142
  1. Detach the 3 claws and open the cover.



    B281143
  1. Remove the rear door inside locking cable.



26. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH


    B277129
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the rear door outside handle cover.



27. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    B277130
  1. Remove the rear door outside handle by sliding and pulling it in the direction indicated by the arrow in the illustration.



28. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    B277131
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the rear door outside handle frame.



29. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    B277132
  1. Detach the 2 claws and remove the rear door front outside handle pad.



30. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    B277133
  1. Detach the 2 claws and remove the rear door rear outside handle pad.



31. REMOVE REAR DOOR PANEL CUSHION


    B281321
  1. Remove the rear door panel cushion.



32. REMOVE REAR DOOR WEATHERSTRIP LH


    B281322
  1. Remove the clip.

  1. Detach the 33 clips and remove the rear door weatherstrip.



33. REMOVE REAR DOOR CHECK ASSEMBLY LH


    B277137
  1. Remove the 3 bolts and rear door check.