Home › DRIVE LINE › DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY

FRONT DIFFERENTIAL CARRIER ASSEMBLY > REASSEMBLY > Preparation



SST 
I000548
09223-00010
Cover & Seal Replacer


I002418
09316-60011
Transmission & Transfer Bearing
Replacer

I002419
(09316-00011)
Replacer Pipe


I000032
09330-00021
Companion Flange Holding Tool


I000883
(09330-00030)
Pin


I000040
09506-30012
Differential Drive Pinion Rear
Bearing Cone Replacer

I000052
09554-22010
Differential Oil Seal Replacer


I106155
09554-47010
Oil Seal Replacer


I000054
09556-22010
Drive Pinion Front Bearing
Remover

I000308
09564-32011
Differential Preload Adaptor


I100843
09564-33010
Drive Pinion Lock Nut Socket


I010020
09930-00010
Drive Shaft Nut Chisel


I010021
(09931-00010)
Handle


I010022
(09931-00020)
Nut Chisel


I002108
09950-30012
Puller A Set


I002109
(09951-03010)
Upper Plate


I002110
(09953-03010)
Center Bolt


I002111
(09954-03010)
Arm


I002142
(09955-03030)
Lower Plate 130


I002144
(09956-03020)
Adapter 18


I002306
09950-60010
Replacer Set


I002342
(09951-00520)
Replacer 52


I002351
(09951-00610)
Replacer 61


I002706
09950-60020
Replacer Set No. 2


I002710
(09951-00720)
Replacer 72


I002716
(09951-00810)
Replacer 81


I002717
(09951-00890)
Replacer 89


I002307
09950-70010
Handle Set


I002356
(09951-07100)
Handle 100


I002357
(09951-07150)
Handle 150




EQUIPMENT
Brass bar

Chisel

Dial indicator

Feeler gauge

Hammer

Micrometer

Needle nose pliers

Plastic-faced hammer

Press

Red lead

Screwdriver

Tape

Torque wrench

Vernier caliper



LUBRICANT
Item
Capacity
Oil grade
Classification
Front differential
1.40 to 1.50 liters (1.48 to 1.59 US qts., 1.23 to 1.31 Imp. qts.)
Hypoid gear oil API GL-4 or GL-5
Above -18°C (0°F): SAE 90
Below -18°C (0°F): SAE 85W-90
Rear differential
3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.90 to 2.99 Imp. qts.)
Hypoid gear oil API GL-5
Above -18°C (0°F): SAE 90
Below -18°C (0°F): SAE 85W-90
w/ Differential lock
2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.60 Imp. qts.)
Made for DANA
2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)


RECOMMENDED TOOLS
I002297
09011-12301
Socket Wrench 30 mm
-
I001889
09013-7C100
Straight Hexagon
10mm
-
I102211
09017-1C100
Union Nut Wrench
10mm
-
I000322
09031-00030
Pin Punch
-
I001236
09044-00010
"TORX" Socket E14
-
I107015
09080-1C110
Toyota Electrical Tester Set
-
I107018
09080-2C100
Test Lead Set
-
I000114
09905-00012
Snap Ring No. 1 Expander
-
I000115
09905-00013
Snap Ring Pliers
-


SSM
Toyota Genuine seal packing 1281, Three Bond 1281 or equivalent
-
Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent
-
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
-