TERMINALS OF ECM
System information · Vehicles built from Aug 2013
Versions by build date: Jun 2011 – Jul 2013 from Aug 2013


- HINT:
- Each ECM terminal's normal voltage is shown in the table below.
- In the table, first follow the information under "Condition". Look under "Symbols (Terminal No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
- Use the illustration above as a reference for the ECM terminals.
| Symbols (Terminal No.) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| BATT (E14-3) - E1 (E17-1) |
L - BR |
Battery (for measuring battery voltage and for ECM memory) |
Always |
9 to 14 V |
| +BM (E14-7) - E1 (E17-1) |
R-W - BR |
Power source of throttle motor |
Always |
9 to 14 V |
| IGSW (E14-9) - E1 (E17-1) |
B-O - BR |
Ignition switch |
Ignition switch ON |
9 to 14 V |
| +B (E14-1) - E1 (E17-1) |
B - BR |
Power source of ECM |
Ignition switch ON |
9 to 14 V |
| +B2 (E14-2) - E1 (E17-1) |
B - BR |
Power source of ECM |
Ignition switch ON |
9 to 14 V |
| OC1+ (E17-17) - OC1- (E17-16) |
L-B - R-B |
Camshaft timing oil control valve (OCV) |
Ignition switch ON |
Pulse generation (see waveform 1) |
| OC2+ (E17-15) - OC2- (E17-14) |
P-L - Y |
Camshaft timing oil control valve (OCV) |
Ignition switch ON |
Pulse generation (see waveform 1) |
| MREL (E14-8) - E1 (E17-1) |
W-G - BR |
MAIN relay |
Ignition switch ON |
9 to 14 V |
| VC (E15-23) - E2 (E15-28) |
LG-B - BR |
Power source for sensors (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
| VG (E15-30) - E2G (E15-29) |
L-W - L-R |
Mass air flow meter |
Idling, Shift lever position P or N, A/C switch OFF |
0.5 to 3.0 V |
| THA (E15-22) - E2 (E15-28) |
L-B - BR |
Intake air temperature sensor |
Idling, Intake air temperature 20°C (68°F) |
0.5 to 3.4 V |
| THW (E15-21) - E2 (E15-28) |
B - BR |
Engine coolant temperature sensor |
Idling, Engine coolant temperature 80°C (176°F) |
0.2 to 1.0 V |
| VTA1 (E15-20) - E2 (E15-28) |
B-R - BR |
Throttle position sensor (for engine control) |
Ignition switch ON, Throttle valve fully closed |
0.5 to 1.2 V |
| VTA1 (E15-20) - E2 (E15-28) |
B-R - BR |
Throttle position sensor (for engine control) |
Ignition switch ON, Throttle valve fully open |
3.2 to 4.8 V |
| VTA2 (E15-19) - E2 (E15-28) |
LG - BR |
Throttle position sensor (for sensor malfunction detection) |
Ignition switch ON, Accelerator pedal released |
2.1 to 3.1 V |
| VTA2 (E15-19) - E2 (E15-28) |
LG - BR |
Throttle position sensor (for sensor malfunction detection) |
Ignition switch ON, Accelerator pedal depressed |
4.5 to 5.0 V |
| VPA (E14-18) - EPA (E14-20) |
W-L - BR-W |
Accelerator pedal position sensor (for engine control) |
Ignition switch ON, Accelerator pedal released |
0.5 to 1.1 V |
| VPA (E14-18) - EPA (E14-20) |
W-L - BR-W |
Accelerator pedal position sensor (for engine control) |
Ignition switch ON, Accelerator pedal depressed |
2.6 to 4.5 V |
| VPA2 (E14-19) - EPA2 (E14-21) |
GR-G - BR-Y |
Accelerator pedal position sensor (for sensor malfunctioning detection) |
Ignition switch ON, Accelerator pedal released |
1.2 to 2.0 V |
| VPA2 (E14-19) - EPA2 (E14-21) |
GR-G - BR-Y |
Accelerator pedal position sensor (for sensor malfunctioning detection) |
Ignition switch ON, Accelerator pedal depressed |
3.4 to 5.0 V |
| VCPA (E14-26) - EPA (E14-20) |
LG-R - BR-W |
Power source of accelerator pedal position sensor (for VPA) |
Ignition switch ON |
4.5 to 5.5 V |
| VCP2 (E14-27) - EPA2 (E14-21) |
BR-R - BR-Y |
Power source of accelerator pedal position sensor (for VPA2) |
Ignition switch ON |
4.5 to 5.5 V |
| HA1A (E16-2) - E04 (E16-7) HA2A (E16-1) - E05 (E16-6) |
Y - W-B R-L - W-B |
A/F sensor heater |
Idling |
Pulse generation (see waveform 2) |
| HA1A (E16-2) - E04 (E16-7) HA2A (E16-1) - E05 (E16-6) |
Y - W-B R-L - W-B |
A/F sensor heater |
Ignition switch ON |
9 to 14 V |
| A1A+ (E16-22) - E1 (E17-1) |
B - BR |
A/F sensor |
Ignition switch ON |
3.3 V * |
| A2A+ (E16-23) - E1 (E17-1) |
G - BR |
A/F sensor |
Ignition switch ON |
3.3 V * |
| A1A- (E16-30) - E1 (E17-1) |
W - BR |
A/F sensor |
Ignition switch ON |
3.0 V * |
| A2A- (E16-31) - E1 (E17-1) |
R - BR |
A/F sensor |
Ignition switch ON |
3.0 V * |
| HT1B (E15-1) - E1 (E17-1) HT2B (E16-5) - E1 (E17-1) |
G - BR L - BR |
Heated oxygen sensor heater |
Idling |
Below 3.0 V |
| HT1B (E15-1) - E1 (E17-1) HT2B (E16-5) - E1 (E17-1) |
G - BR L - BR |
Heated oxygen sensor heater |
Ignition switch ON |
9 to 14 V |
| OX1B (E15-18) - E2 (E15-28) OX2B (E16-33) - E2 (E15-28) |
W - BR B - BR |
Heated oxygen sensor |
Maintain engine speed at 2,500 rpm for 2 minutes after warming up |
Pulse generation (see waveform 3) |
| #10 (E17-2) - E01 (E15-7) #20 (E17-3) - E01 (E15-7) #30 (E17-4) - E01 (E15-7) #40 (E17-5) - E01 (E15-7) #50 (E17-6) - E01 (E15-7) #60 (E17-7) - E01 (E15-7) |
L - W-B G - W-B R - W-B W - W-B L - W-B Y - W-B |
Injector |
Ignition switch ON |
9 to 14 V |
| #10 (E17-2) - E01 (E15-7) #20 (E17-3) - E01 (E15-7) #30 (E17-4) - E01 (E15-7) #40 (E17-5) - E01 (E15-7) #50 (E17-6) - E01 (E15-7) #60 (E17-7) - E01 (E15-7) |
L - W-B G - W-B R - W-B W - W-B L - W-B Y - W-B |
Injector |
Idling |
Pulse generation (see waveform 4) |
| IGT1 (E15-8) - E1 (E17-1) IGT2 (E15-9) - E1 (E17-1) IGT3 (E15-10) - E1 (E17-1) IGT4 (E15-11) - E1 (E17-1) IGT5 (E15-12) - E1 (E17-1) IGT6 (E15-13) - E1 (E17-1) |
R - BR R-L - BR G-B - BR G - BR B-L - BR P-L - BR |
Ignition coil (ignition signal) |
Idling |
Pulse generation (see waveform 7) |
| KNK1 (E16-29) - EKNK (E16-28) |
B - W |
Knock sensor |
Maintain engine speed at 4,000 after warming up |
Pulse generation (see waveform 5) |
| KNK2 (E16-21) - EKN2 (E16-20) |
R - G |
Knock sensor |
Maintain engine speed at 4,000 after warming up |
Pulse generation (see waveform 5) |
| VV1+ (E17-19) - VV1- (E17-29) |
R - G |
Variable valve timing (VVT) sensor |
Idling |
Pulse generation (see waveform 6) |
| VV2+ (E17-18) - VV2- (E17-28) |
Y - L |
Variable valve timing (VVT) sensor |
Idling |
Pulse generation (see waveform 6) |
| NE+ (E17-21) - NE- (E17-20) |
B - W |
Crankshaft position sensor |
Idling |
Pulse generation (see waveform 6) |
| IGF1 (E15-24) - E1 (E17-1) |
G-R - BR |
Ignition coil (ignition confirmation signal) |
Ignition switch ON |
4.5 to 5.5 V |
| IGF1 (E15-24) - E1 (E17-1) |
G-R - BR |
Ignition coil (ignition confirmation signal) |
Idling |
Pulse generation (see waveform 7) |
| PRG (E15-34) - E1 (E17-1) |
L - BR |
VSV for EVAP |
Ignition switch ON |
9 to 14 V |
| PRG (E15-34) - E1 (E17-1) |
L - BR |
VSV for EVAP |
Idling |
Pulse generation (see waveform 8) |
| SPD (E13-8) - E1 (E17-1) |
V-R - BR |
Speed signal from combination meter |
Ignition switch ON, Rotate driving wheel slowly |
Pulse generation (see waveform 9) |
| STA (E17-11) - E1 (E17-1) |
B-Y - BR |
Starter signal |
Cranking |
9 to 14 V |
| NSW (E16-8) - E1 (E17-1) |
L-Y - BR |
Park/Neutral position switch signal |
Ignition switch ON, Other shift position not in P or N |
9 to 14 V |
| NSW (E16-8) - E1 (E17-1) |
L-Y - BR |
Park/Neutral position switch signal |
Ignition switch ON, Shift position in P or N |
0 to 3.0 V |
| STP (E14-15) - E1 (E17-1) |
G-W - BR |
Stop light switch |
Brake pedal depressed |
7.5 to 14 V |
| STP (E14-15) - E1 (E17-1) |
G-W - BR |
Stop light switch |
Brake pedal released |
Below 1.5 V |
| ST1- (E14-16) - E1 (E17-1) |
R-L - BR |
Stop light switch (ST1 terminal status is opposite to STP terminal) |
Ignition switch ON, Brake pedal depressed |
Below 1.5 V |
| ST1- (E14-16) - E1 (E17-1) |
R-L - BR |
Stop light switch (ST1 terminal status is opposite and STP terminal) |
Ignition switch ON, Brake pedal released |
7.5 to 14 V |
| M+ (E15-5) - ME01 (E16-3) |
B - W-B |
Throttle actuator |
Idling with warm engine |
Pulse generation (see waveform 10) |
| M- (E15-4) - ME01 (E16-3) |
W - W-B |
Throttle actuator |
Idling with warm engine |
Pulse generation (see waveform 11) |
| FC (E14-10) - E1 (E17-1) |
LG-B - BR |
Fuel pump control |
Ignition switch ON |
9 to 14 V |
| FPR (E17-30) - E1 (E17-1) |
P-L - BR |
Fuel pump control |
Ignition switch ON, STA signal OFF |
0 to 3.0 V |
| FPR (E17-30) - E1 (E17-1) |
P-L - BR |
Fuel pump control |
Ignition switch ON, STA signal ON |
9 to 14 V |
| W (E13-30) - E1 (E17-1) |
R-B - BR |
MIL |
Ignition switch ON |
Below 3.0 V |
| W (E13-30) - E1 (E17-1) |
R-B - BR |
MIL |
Idling |
9 to 14 V |
| TC (E14-23) - E1 (E17-1) |
P-B - BR |
Terminal TC of DLC3 |
Ignition switch ON |
9 to 14 V |
| SIL (E14-30) - E1 (E17-1) |
R-Y - BR |
Terminal SIL of DLC3 |
Connect intelligent tester to DLC3 |
Pulse generation |
| TACH (E13-1) - E1 (E17-1) |
B-W - BR |
Engine speed |
Idling |
Pulse generation (see waveform 12) |
| ACIS (E15-33) - E1 (E17-1) |
G-B - BR |
VSV for ACIS |
Ignition switch ON |
9 to 14 V |
| PSW (E17-10) - E1 (E17-1) |
G-Y - BR |
Power steering pressure switch |
Ignition switch ON |
9 to 14 V |
- HINT:
- *: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
| WAVEFORM 1 |
![]() ![]() |
- Camshaft timing Oil Control Valve (OCV)
| Item |
Content |
| Symbols (Terminal No.) |
OC1+ (E17-17) - OC1- (E17-16) OC2+ (E17-15) - OC2- (E17-14) |
| Tool Setting |
5 V/DIV., 1 msec./DIV. |
| Condition |
Idling |
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
| WAVEFORM 2 |
![]() ![]() |
- A/F sensor heater
| Item |
Content |
| Symbols (Terminal No.) |
HA1A (E16-2) - E04 (E16-7) HA2A (E16-1) - E05 (E16-6) |
| Tool Setting |
5 V/DIV., 10 msec./DIV. |
| Condition |
Idling |
| WAVEFORM 3 |
![]() ![]() |
- Heated oxygen sensor
| Item |
Content |
| Symbols (Terminal No.) |
OX1B (E15-18) - E2 (E15-28) OX2B (E16-33) - E2 (E15-28) |
| Tool Setting |
0.2 V/DIV., 200 msec./DIV. |
| Condition |
Engine speed maintained at 2,500 rpm for 2 minutes after warming up engine |
- HINT:
- In the Data List, item O2S B1S2 shows the ECM input values from the heated oxygen sensor.
| WAVEFORM 4 |
![]() ![]() |
- Fuel injector
| Item |
Content |
| Symbols (Terminal No.) |
#10 (E17-2) - E01 (E15-7) #20 (E17-3) - E01 (E15-7) #30 (E17-4) - E01 (E15-7) #40 (E17-5) - E01 (E15-7) #50 (E17-6) - E01 (E15-7) #60 (E17-7) - E01 (E15-7) |
| Tool Setting |
30 V/DIV., 20 msec./DIV. |
| Condition |
Idling |
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
| WAVEFORM 5 |
![]() ![]() |
- Knock sensor
| Item |
Content |
| Symbols (Terminal No.) |
KNK1 (E16-29) - EKNK (E16-28) KNK2 (E16-21) - EKN2 (E16-20) |
| Tool Setting |
0.01 to 10 V/DIV., 0.01 to 10 msec./DIV. |
| Condition |
Maintain engine speed at 4,000 rpm after warming up engine |
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
- The waveform and amplitude displayed differ slightly depending on the vehicle.
- The wavelength becomes shorter as the engine rpm increases.
| WAVEFORM 6 |
![]() ![]() |
- (a) Crankshaft position sensor
- (b) VVT sensor bank 1
- (c) VVT sensor bank 2
| Item |
Content |
| Symbols (Terminal No.) |
NE+ (E17-21) - NE- (E17-20) VV1+ (E17-19) - VV1- (E17-29) VV2+ (E17-18) - VV2- (E17-28) |
| Tool Setting |
5 V/DIV., 20 msec./DIV. |
| Condition |
Idling |
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
| WAVEFORM 7 |
![]() ![]() |
- (a) Igniter IGT signal (from ECM to igniter)
- (b) Igniter IGF signal (from igniter to ECM)
| Item |
Content |
| Symbols (Terminal No.) |
IGT1 (E15-8) - E1 (E17-1) IGT2 (E15-9) - E1 (E17-1) IGT3 (E15-10) - E1 (E17-1) IGT4 (E15-11) - E1 (E17-1) IGT5 (E15-12) - E1 (E17-1) IGT6 (E15-13) - E1 (E17-1) IGF1 (E15-24) - E1 (E17-1) |
| Tool Setting |
2 V/DIV., 20 msec./DIV. |
| Condition |
Idling |
- HINT:
- The wavelength becomes shorter as the engine rpm increases.
| WAVEFORM 8 |
![]() ![]() |
- VSV for EVAP
| Item |
Content |
| Symbols (Terminal No.) |
PRG (E15-34) - E1 (E17-1) |
| Tool Setting |
10 V/DIV., 20 msec./DIV. |
| Condition |
Idling |
- HINT:
- If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.
| WAVEFORM 9 |
![]() ![]() |
- Vehicle speed signal
| Item |
Content |
| Symbols (Terminal No.) |
SPD (E13-8) - E1 (E17-1) |
| Tool Setting |
2 V/DIV., 20 msec./DIV. |
| Condition |
Driving at 20 mph (12 km/h) |
- HINT:
- The wavelength becomes shorter as the vehicle speed increases.
| WAVEFORM 10 |
![]() ![]() |
- Throttle actuator positive terminal
| Item |
Content |
| Symbols (Terminal No.) |
M+ (E15-5) - ME01 (E16-3) |
| Tool Setting |
5 V/DIV., 1 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The duty ratio varies depending on the throttle actuator operation.
| WAVEFORM 11 |
![]() ![]() |
- Throttle actuator negative terminal
| Item |
Content |
| Symbols (Terminal No.) |
M- (E15-4) - ME01 (E16-3) |
| Tool Setting |
5 V/DIV., 1 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The duty ratio varies depending on the throttle actuator operation.
| WAVEFORM 12 |
![]() ![]() |
- Engine speed signal
| Item |
Content |
| Symbols (Terminal No.) |
TACH (E13-1) - E1 (E17-1) |
| Tool Setting |
5 V/DIV., 10 msec./DIV. |
| Condition |
Idling |
- HINT:
- The wavelength becomes shorter as the engine rpm increases.











