2014 Hilux · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Jun 2011


1. INSTALL PLANET CARRIER SHAFT SUB-ASSEMBLY
  1. Install the 3 damper rubbers and the intermediate sealing to the planet carrier.

  1. A117267E01
    Install the planet carrier shaft to the planet carrier.

  1. Install the washer to the planet carrier shaft.

  1. A105363
    Using a screwdriver and hammer, tap on a new snap ring.


2. INSTALL STARTER CLUTCH SUB-ASSEMBLY

  1. A121935E01
    Apply MP grease to the spline of the starter clutch sub-assembly and planet carrier shaft.

  1. Install the starter clutch to the planet carrier shaft.

  1. A104907E04
    Apply MP grease to a new snap ring and the pinion stop collar.

  1. Install the pinion stop collar and snap ring.

  1. A104906E01
    Using a vise, compress the snap ring.

  1. A033587E01
    Using a plastic-faced hammer, lightly tap the planet carrier shaft while holding the outside of the starter clutch sub-assembly by hand until the pinion stop collar and snap ring are as shown in the illustration.

  1. A198324E01
    Apply MP grease to the pinion drive lever.

  1. A121928E02
    Install the starter clutch sub-assembly, pinion drive lever and cover to the starter drive housing.

  1. A198325E01
    Apply MP grease to the planetary gears and pin parts of the planet carrier shaft.

  1. Install the 3 planetary gears to the planet carrier.


3. INSTALL STARTER ARMATURE ASSEMBLY

  1. A105361E01
    Install the starter armature to the starter yoke.


4. INSTALL STARTER BRUSH HOLDER ASSEMBLY

NOTICE:
Do not drop the starter armature assembly.

  1. A200784E01
    Hold the starter yoke assembly between aluminum plates in a vise.

    NOTICE:
    Do not damage the starter yoke.

  1. While compressing the springs, install the starter brush holder to the starter armature.

    NOTICE:
    Align the cutout of the starter yoke and the rubber part and install the starter brush holder.

  1. A121926E01
    Install the starter commutator end frame to the starter yoke.

  1. Install the washer to the starter commutator end frame.

  1. A121925E01
    Apply MP grease to the slotted washer and install it.

  1. Install the seal ring.

  1. A121924
    Install the starter commutator end frame cover to the starter commutator end frame with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }


5. INSTALL STARTER YOKE ASSEMBLY

  1. A121936E01
    Fit the 3 claws of the plate into the 3 grooves of the planet carrier to install the plate to the planet carrier.

  1. Install the cover ring to the planet carrier.

  1. A121937E01
    Align the groove of the starter yoke assembly and the starter drive housing cover and install the starter yoke assembly to the starter drive housing.

  1. A121922
    Install the 2 bolts.

    Torque:
    4.8 N*m{ 48 kgf*cm , 42 in.*lbf }


6. INSTALL MAGNET STARTER SWITCH ASSEMBLY

  1. A121921E01
    Apply MP grease to the hook.

  1. Install the plunger to the pinion drive lever.

  1. A121920
    Install the return spring to the magnet starter switch assembly.

  1. Using a T25 "TORX" socket wrench, install the magnet starter switch assembly with the 3 screws.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. A121919
    Connect the lead wire to terminal C with the nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

← INSPECTION (from Jun 2011)INSTALLATION (Jun 2011 – Jul 2012) →