P0617 Starter Relay Circuit High
Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
DESCRIPTION
While the engine is being cranked, positive (+) battery voltage is applied to terminal STA of the ECM.If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it will conclude that there is fault in the starter control circuit. The ECM will turn on the Malfunction Indicator Lamp (MIL) and set a DTC.
This monitor runs when the vehicle is driven at 20 km/h (12 mph) for over 20 seconds.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0617 |
Following conditions are met for 20 seconds:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. READ DATA LIST (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter SIG.
Confirm the starter signal status when the ignition switch is operated.
- OK:
Ignition Switch Position
Starter Signal
ON
OFF
START
ON
|
|
||||
| NG | |
| 2. INSPECT PARK/NEUTRAL POSITION SWITCH (A/T) OR WIRE HARNESS (ECM - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
![]() ![]() ![]() ![]() |
A/T:Inspect the Park/Neutral Position (PNP) switch.(1) Disconnect the N8 switch connector.(2) Measure the resistance when the shift lever is moved to each position.
- Standard resistance:
Tester Connection
Shift Lever Position
Specified Condition
4 - 5
P
Below 1 Ω
4 - 5
N
Below 1 Ω
M/T:Disconnect the E17 ECM connector.
Disconnect the 2O junction block connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
2O-19 - E17-11 (STA)
Below 1 Ω
2O-19 or E17-11 (STA) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 3. READ DATA LIST (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter SIG.
Confirm the starter signal status when the ignition switch is operated.
- OK:
Ignition Switch Position
Starter Signal
ON
OFF
START
ON
|
|
||||
| NG | |
| 4. INSPECT IGNITION SWITCH ASSEMBLY |
![]() ![]() |
Disconnect the I6 ignition switch connector.
Measure the resistance of the ignition switch.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
5 (AM2) - 7 (ST2)
OFF
10 kΩ or higher
5 (AM2) - 7 (ST2)
START
Below 1 Ω
|
|
||||
| OK | |
| 5. READ DATA LIST (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter SIG.
Confirm the starter signal status when the ignition switch is operated.
- OK:
Ignition Switch Position
Starter Signal
ON
OFF
START
ON
|
|
||||
| OK | ||
| ||



