2014 Hilux · Service Manual ENGINE

ECM Power Source Circuit

Circuit diagnosis · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the ignition switch is turned ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes a current to flow to the coil, closing the contacts of the MAIN relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A119983E01

INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs initialization (Click here).


1. CHECK ECM (+B VOLTAGE)

  1. A018294E34
    Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    E5-1 (+B) - E7-7 (E1)
    9 to 14 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN ON PROBLEM SYMPTOMS TABLE
NG


2. CHECK WIRE HARNESS (ECM - BODY GROUND)

  1. A065745E08
    Disconnect the E7 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E7-7 (E1) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. CHECK ECM (IGSW VOLTAGE)

  1. A018294E35
    Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    E5-9 (IGSW) - E7-7 (E1)
    9 to 14 V



OK
Go to step 6
NG


4. INSPECT FUSE (IGN FUSE)

  1. F050101E01
    Remove the IGN fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


5. INSPECT IGNITION SWITCH ASSEMBLY

  1. A056879E16
    Disconnect the I9 ignition switch connector.

  1. Measure the resistance of the ignition switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (AM2) - 6 (IG2)
    LOCK
    10 kΩ or higher
    5 (AM2) - 6 (IG2)
    ON
    Below 1 Ω



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK


6. CHECK ECM (MREL VOLTAGE)

  1. A018294E36
    Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    E5-8 (MREL) - E7-7 (E1)
    9 to 14 V



NG
REPLACE ECM
OK


7. INSPECT FUSE (EFI FUSE)

  1. A099789E09
    Remove the EFI fuse from the engine room junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


8. INSPECT INTEGRATION NO.1 RELAY (MAIN RELAY)

  1. G039047E07
    Remove the integration relay from the engine room junction block (Click here).

  1. Disconnect the 1J integration relay connector.

  1. Measure the voltage of the MAIN relay.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1J-4 - Body ground
    Ignition switch ON
    10 to 14 V



NG
REPLACE ECM
OK


9. CHECK WIRE HARNESS (INTEGRATION RELAY (MAIN RELAY) - ECM)

  1. G034918E02
    Disconnect the 1J integration relay connector from the engine room junction block (Click here).

  1. Disconnect the E5 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    1J-4 - E5-1 (+B)
    Below 1 Ω
    1J-4 or E5-1 (+B) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (+B TERMINAL OF ECM - BATTERY POSITIVE TERMINAL)


← Turbocharger Noise (from Aug 2014)ECM Power Source Circuit (Aug 2012 – Jul 2013) →