DATA LIST / ACTIVE TEST
System information · Vehicles built Nov 2011 – Jul 2013
Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
| READ DATA LIST |
- HINT:
- By reading the Data List displayed on the intelligent tester, you can check values, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.
- NOTICE:
- In the table below, the values listed under Normal Conditions are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.
Warm up the engine.
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Check the values by referring to the following table.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Notes
Coolant Temp
(COOLANT TEMP)
Engine coolant temperature:
Min.: -40°C, Max.: 215°C
80 to 95°C (176 to 203°F):
After warming up engine
If value -40°C or 140°C, sensor circuit open or shorted
PIM
(PIM)
Absolute pressure inside intake manifold:
Min.: 0 kPa, Max.: 255 kPa
- 90 to 105 kPa:
Idling
- 88 to 103 kPa:
Engine running at 2,000 rpm
- 85 to 100 kPa:
Engine running at 3,000 rpm
-
Engine SPD
(ENGINE SPD)
Engine speed:
Min.: 0 rpm, Max.: 16383.75 rpm
720 to 820 rpm: Idling (A/C off)
After warming up engine
-
Vehicle SPD
(VEHICLE SPD)
Vehicle speed:
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed
Speed indicated on speedometer
Intake Air
(INTAKE AIR)
Intake air temperature:
Min.: -40°C, Max.: 215°C
Equivalent to temperature at intake manifold
If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Injection Volume
(INJ VOLUME)
Injection volume:
Min.: 0 mm3, Max.: 1279.98 mm3
3 to 11 mm3: Idling
-
Injection Timing
(INJ TIMING)
Injection timing:
Min.: 0 CA, Max.: 51 CA
16 to 20 CA: Idling
After warming up engine
-
Fuel Temp.
(FUEL TEMP)
Fuel temperature status:
Min.: -40°C, Max.: 215°C
Actual fuel temperature
If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Accel Position
(ACCEL POSITION)
Accelerator position status:
Min.: 0%, Max.: 100%
- 10 to 22%:
Accelerator pedal released
- 52 to 90%:
Accelerator pedal depressed
Read value with ignition switch ON (Do not start engine)
Throttle Step POS
(THROTTLE POS)
Throttle step position:
Min.: 1 step, Max.: 255 step
- 209 step: Throttle fully closed
- 0 step: Throttle fully open
Read value with ignition switch ON (Do not start engine)
#Codes
(#CODES)
Number of memorized DTC codes:
Min.: 0, Max.: 255
0
-
Stop Light SW
(STOP LIGHT SW)
Stop light switch:
ON or OFF
- ON: Brake pedal depressed
- OFF: Brake pedal released
-
A/C SIG
(A/C SIGNAL)
A/C signal:
ON or OFF
ON: A/C switch is turned ON
-
Starter SIG
(STARTER SIG)
Starter signal: ON or OFF
ON: Cranking
-
Accel Open SW
(ACCEL OPEN SW)
Accelerator pedal open switch:
ON or OFF
OFF: Accelerator pedal released
-
SPD Test
(SPD Test)
Check mode result for vehicle speed sensor:
0: COMPL, 1: INCOMPL
-
Click here
Check Mode
(CHECK MODE)
Check mode: ON or OFF
ON: Check mode ON
-
A/C Cut SIG
(A/C CUT SIG)
A/C cut signal: ON or OFF
ON: A/C compressor ON
-
- HINT:
- Normal Condition: If no idling conditions are specified, the shift lever should be in the neutral position, and the A/C switch and all accessory switches should be off.
- 90 to 105 kPa:
| PERFORM ACTIVE TEST |
- HINT:
- Performing the Active Test enables components, including the relays, VSV (Vacuum Switching Valve), and actuators, to be operated without removing any parts. The Active Test can be performed with the intelligent tester. Performing the Active Test as a first step of troubleshooting is one method of shortening diagnostic time.
- The Data List can be displayed during Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Tests by referring to the following table.
Tester Display
Test Part
Control Range
Diagnostic Note
A/C Cut Signal
Control A/C cut signal
ON/OFF
-
TC/TE1
Turn ON and OFF TC and TE1 connection
ON/OFF
- ON: TC and TE1 connected
- OFF: TC and TE1 disconnected
- ON: TC and TE1 connected