2014 Hilux · Service Manual TRANSMISSION

TERMINALS OF ECU

System information · Vehicles built from Aug 2012


CHECK TCM
C214981E12

HINT:
The standard voltage at each TCM terminal is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to inspect. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the TCM terminals.

Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
T19-12 (NSW) - T19-1 (E1)
L-Y - BR
PNP switch signal
  1. Ignition switch ON
  2. Shift lever in P or N
Below 1 V
  1. Ignition switch ON
  2. Shift lever not in P or N
11 to 14 V
T37-9 (R) - T19-1 (E1)
R-Y - BR
R shift position switch signal
  1. Ignition switch ON
  2. Shift lever in R
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in R
Below 1 V
T37-8 (D) - T19-1 (E1)
G-Y - BR
D shift position switch signal
  1. Ignition switch ON
  2. Shift lever in D or 3
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in D or 3
Below 1 V
T37-12 (3) - T19-1 (E1)
G-O - BR
3 shift position switch signal
  1. Ignition switch ON
  2. Shift lever in 3
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in 3
Below 1 V
T37-11 (2) - T19-1 (E1)
L - BR
2 shift position switch signal
  1. Ignition switch ON
  2. Shift lever in 2
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in 2
Below 1 V
T37-10 (L) - T19-1 (E1)
G-R - BR
L shift position switch signal
  1. Ignition switch ON
  2. Shift lever in L
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in L
Below 1 V
T19-18 (S1) - T19-1 (E1)
GR - BR
S1 solenoid signal
1st or 2nd gear
11 to 14 V
3rd or 4th gear
Below 1 V
T19-17 (S2) - T19-1 (E1)
W-L - BR
S2 solenoid signal
2nd or 3rd gear
11 to 14 V
1st or 4th gear
Below 1 V
T19-20 (SLT+) - T19-19 (SLT-)
G-Y - L-B
SLT solenoid signal
Engine idling
Pulse generation
T19-16 (SL) - T19-1 (E1)
G - BR
SL solenoid signal
Vehicle speed 65 km/h (40 mph), lock-up (ON to OFF)
Pulse generation
(See waveform 1)
Vehicle driving under look-up condition
11 to 14 V
T19-24 (THOC) - T19-23 (E2)
BR - B-Y
ATF temperature sensor signal
ATF temperature: 115°C (239°F) or higher
Below 1.5 V
T19-30 (SP2+) - T19-29 (SP2-)
R - G
Speed sensor SP2 signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(See waveform 2)
T19-3 (NC0+) - T19-2 (NC0-)
V - P
Speed sensor NC0 signal
Engine idling
(shift lever in P or N)
Pulse generation
(See waveform 3)
T37-15 (L4) - T19-1 (E1)
G-W - BR
L4 position signal
  1. Ignition switch ON
  2. Transfer in L4
Below 1 V
  1. Ignition switch ON
  2. Transfer not in L4
11 to 14 V
T38-25 (SPD1) - T19-1 (E1)
V-R - BR
Speed signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(See waveform 4)
T38-14 (STP) - T19-1 (E1)
G-W - BR
STP light switch signal
Brake pedal is depressed
7.5 to 14 V
Brake pedal is released
Below 1 V
T19-11 (STA) - T19-1 (E1)
B-Y - BR
Starter signal
Cranking
6 V or more
T37-16 (TFN) - T19-1 (E1)
W-G - BR
N shift position switch signal
  1. Ignition switch ON
  2. Transfer shift lever on N
Below 1 V
  1. Ignition switch ON
  2. Transfer shift lever not on N
11 to 14 V
T38-6 (IG2) - T19-1 (E1)
B-O - BR
Ignition switch
Ignition switch ON
11 to 14 V
T38-21 (CAN+) - T19-1 (E1)
V - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 5)
T38-20 (CAN-) - T19-1 (E1)
P - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 6)

  1. C170572E01
    Using an oscilloscope, check waveform 1.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    T19-16 (SL) - T19-1 (E1)
    10 V/DIV., 100 msec./DIV.
    Vehicle speed 65 km/h (40 mph), lock-up (ON to OFF)

  2. C170571E02
    Using an oscilloscope, check waveform 2.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    T19-30 (SP2+) - T19-29 (SP2-)
    2 V/DIV., 20 msec./DIV.
    Vehicle speed 20 km/h (12 mph)

  3. C170570E01
    Using an oscilloscope, check waveform 3.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    T19-3 (NC0+) - T19-2 (NC0-)
    5 V/DIV., 0.5 msec./DIV.
    Engine idling (shift lever in P or N)

  4. C170574E01
    Using an oscilloscope, check waveform 4.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    T38-25 (SPD1) - T19-1 (E1)
    5 V/DIV., 20 msec./DIV.
    Vehicle speed 20 km/h (12 mph)

  5. C175015E01
    Using an oscilloscope, check waveform 5.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    T38-21 (CAN+) - T19-1 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON

  6. C175016E01
    Using an oscilloscope, check waveform 6.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    T38-20 (CAN-) - T19-1 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON


CHECK ECM
C115871E19

HINT:
The standard voltage at each ECM terminal is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to inspect. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.

Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E5-1 (+B) - E7-7 (E1)
B - BR
Power source of ECM
Ignition switch ON
11 to 14 V
E6-22 (CAN+) - E7-7 (E1)
V - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 1)
E6-21 (CAN-) - E7-7 (E1)
P - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 2)

  1. C175015E01
    Using an oscilloscope, check waveform 1.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    E6-22 (CAN+) - E7-7 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON

  2. C175016E01
    Using an oscilloscope, check waveform 2.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    E6-21 (CAN-) - E7-7 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON

← PROBLEM SYMPTOMS TABLE (from Aug 2014)DIAGNOSIS SYSTEM (Aug 2012 – Jul 2013) →