DATA LIST / ACTIVE TEST
System information · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 from Aug 2012
| READ DATA LIST |
- HINT:
- Using the intelligent tester's Data List allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / ECT / Data List.
Follow the instructions on the tester and read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
Speed indicated on speedometer
Engine Speed
Engine speed/
Min.: 0 rpm
Max.: 16383.75 rpm
Engine idling: 700 to 800 rpm
-
Calculate Load
Calculated load by ECM/
Min.: 0%
Max.: 100%
Running without load (2500 rpm): 13.1 to 18.9%
-
Coolant Temp
Engine coolant temperature/
Min.: -40°C (-40°F)
Max.: 140°C (284°F)
After warming up engine: 80 to 90°C (176 to 194°F)
- If the value is -40°C (-40°F), the sensor circuit is open.
- If the value is 140°C (284°F), the sensor circuit is shorted.
Engine Run Time
Engine run time/
Min.: 0 seconds,
Max.: 65535 seconds
Time after engine start
-
Battery Voltage
Battery voltage/
Min.: 0 V
Max.: 65.535 V
Engine idling: 11 to 14 V
-
Starter Signal
Starter signal/
ON or OFF
- ON: Engine cranking
- OFF: Engine not cranking
-
Neutral Position SW Signal
PNP switch status/
ON or OFF
Shift lever is:
On P or N: ON
Not on P or N: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect - HINT:
- When failure still occurs even after adjusting these parts, Click here, Click here
Stop Light Switch
Stop light switch status/
ON or OFF
- Brake pedal is depressed: ON
- Brake pedal is released: OFF
-
Check Mode
Check mode/
ON or OFF
ON: Check mode ON
-
SPD Test Result
Check mode result for vehicle/
Compl or Incmpl
-
-
Complete Parts Monitor
Comprehensive component monitor/
Not Avl or Avail
-
-
Fuel System Monitor
Fuel system monitor/
Not Avl or Avail
-
-
Misfire Monitor
Misfire monitor/
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor/
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor/
Compl or Incmpl
-
-
O2S(A/FS) Heater Monitor
Heated oxygen sensor (air fuel ratio sensor) heater monitor/
Not Avl or Avail
-
-
O2S(A/FS) Heater Monitor
Heated oxygen sensor (air fuel ratio sensor) heater monitor/
Compl or Incmpl
-
-
O2S(A/FS) Monitor
Heated oxygen sensor (air fuel ratio sensor) monitor/
Not Avl or Avail
-
-
O2S(A/FS) Monitor
Heated oxygen sensor (air fuel ratio sensor) monitor/
Compl or Incmpl
-
-
A/C Monitor
A/C monitor/
Not Avl or Avail
-
-
A/C Monitor
A/C monitor/
Compl or Incmpl
-
-
2nd Air Monitor
2nd air monitor/
Not Avl or Avail
-
-
2nd Air Monitor
2nd air monitor/
Compl or Incmpl
-
-
EVAP Monitor
EVAP monitor/
Not Avl or Avail
-
-
EVAP Monitor
EVAP monitor/
Compl or Incmpl
-
-
Heated Catalyst Monitor
Heated catalyst monitor/
Not Avl or Avail
-
-
Heated Catalyst Monitor
Heated catalyst monitor/
Compl or Incmpl
-
-
Catalyst Monitor
Catalyst monitor/
Not Avl or Avail
-
-
Catalyst Monitor
Catalyst monitor/
Compl or Incmpl
-
-
# Codes (Include History)
# of Codes/
Min.: 0
Max.: 255
-
Number of detected DTCs
MIL
MIL status/
ON or OFF
ON: MIL ON
-
MIL ON Run Distance
MIL ON run distance/
Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile)
Distance after DTC stored
-
Running Time from MIL ON
Running time from MIL on/
Min.: 0 minutes,
Max.: 65535 minutes
Equivalent to running time after MIL turns on
-
Time after DTC Cleared
Time after DTC cleared/
Min.: 0 minutes,
Max.: 65535 minutes
Equivalent to time after DTCs cleared
-
Distance from DTC Cleared
Distance after DTC cleared/
Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile)
Equivalent to distance driven after DTCs cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared/
Min.: 0, Max.: 255
-
Number of warm-up cycles after DTCs cleared
Number of Emission DTC
Number of emission DTCs
-
-
Model Code
Model Code/
-
-
Engine Type
Engine Type/
-
-
Cylinder Number
Cylinder number/
-
-
Destination
Destination/
-
-
Model Year
Model year/
-
-
Engine Speed from EFI
Engine speed/
Min.: 0 rpm
Max.: 16383.75 rpm
-
Engine speed received from the ECM.
Intake-Air Temp from EFI
Intake air temperature/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
-
Intake air temperature received from the ECM.
Coolant Temp from EFI
Engine coolant temperature/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
-
Coolant temperature received from the ECM.
Accel Position from EFI
Absolute accelerator pedal position/
Min.: 0%
Max.: 100%
-
-
Injection Volume from EFI
Injection volume/
Min.: -10 mm3
Max.: 1,279.98 mm3
-
-
SPD (NC0)
Input turbine speed/
Min.: 0 rpm
Max.: 12750 rpm
- Lock-up ON (warmed up engine, other than O/D):
Input turbine speed (NC0) is equal to the engine speed
- Lock-up ON (warmed up engine, O/D):
Input turbine speed (NC0) is 0 rpm
- Lock-up OFF (idling with shift lever on N):
Input turbine speed (NC0) is nearly equal to engine speed
-
SPD (SP2)
Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph)
(output shaft speed is equal to vehicle speed)
-
Shift SW Status (R Range)
PNP switch status/
ON or OFF
Shift lever is:
On R: ON
Not on R: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect - HINT:
- When failure still occurs even after adjusting these parts, Click here, Click here
Shift SW Status (2 Range)
PNP switch status/
ON or OFF
Shift lever is:
On 2: ON
Not on 2: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect - HINT:
- When failure still occurs even after adjusting these parts, Click here, Click here
Shift SW Status (L Range)
PNP switch status/
ON or OFF
Shift lever is:
On L: ON
Not on L: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect - HINT:
- When failure still occurs even after adjusting these parts, Click here, Click here
Shift SW Status (D Range)
PNP switch status/
ON or OFF
Shift lever is:
On D: ON
Not on D: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect - HINT:
- When failure still occurs even after adjusting these parts, Click here, Click here
Shift SW Status (3 Range)
PNP switch status/
ON or OFF
Shift lever is:
On 3: ON
Not on 3: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect - HINT:
- When failure still occurs even after adjusting these parts, Click here, Click here
A/T Oil Temperature 3
ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
- After stall test:
Approximately 80°C (176°F)
- Equal to ambient temperature during engine is cold
If value is -40°C (-40°F) or 215°C (419°F), ATF temperature sensor circuit is opened or short circuited
Lock Up
Lock-up/
ON or OFF
- ON: Lock-up operating
- OFF: Lock-up not operating
-
Lock Up Solenoid Status
Lock-up solenoid status/
ON or OFF
- Lock-up: ON
- Not on lock-up: OFF
-
Shift Status
ECM gear shift command/
1st, 2nd, 3rd or 4th (O/D)
Shift lever position is: - On L: 1st
- On 2: 1st or 2nd
- On D (O/D OFF): 1st, 2nd or 3rd
- On D (O/D ON): 1st, 2nd, 3rd or 4th (O/D)
-
SLT Solenoid Status
Shift solenoid SLT status/
ON or OFF
- Accelerator pedal is depressed: OFF
- Accelerator pedal is released: ON
-
- If the value is -40°C (-40°F), the sensor circuit is open.
| PERFORM ACTIVE TEST |
- HINT:
- Performing the intelligent tester's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.
- The Data List can be displayed during the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / ECT / Active Test.
Perform the Active Test.
Tester Display
Test Part
Control Range
Diagnostic Note
Connect the TC and TE1
Turn on and off TC and TE1 connection
ON or OFF
-
Activate the Solenoid (SLT)*
Operate shift solenoid valve SLT and raise line pressure
ON or OFF - HINT:
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)
- ON: No action (normal operation)
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)
[Vehicle Condition] - Vehicle stopped
- Engine idling
Activate the Solenoid (S1)
Operate shift solenoid valve S1
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Solenoid (S2)
Operate shift solenoid valve S2
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Lock Up
Control shift solenoid valve SLT to set automatic transmission to lock-up
ON or OFF
Possible to check shift solenoid valve SLT operation.
[Vehicle Condition]- Throttle valve opening angle: Less than 35%
- Vehicle speed: 60 km/h (37 mph) or more
Activate the Solenoid (SL)
Operate shift solenoid valve SL
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Control the Shift Position
Operate shift solenoid valves and set each shift position
- Press "→" button: Shift up
- Press "←" button: Shift down
Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (31 mph) or less
- HINT:
- *: "Control the Line Pressure Up" in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.