2014 Hilux · Service Manual TRANSMISSION

P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012

DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the TCM.
DTC Code
DTC Detection Condition
Trouble Area
P0705
When either condition below is met (2 trip detection logic):
  1. All switches are OFF simultaneously for P, R, N, D, 3 and 2 positions
  1. 2 or more switches are ON simultaneously for D, 4, 3, 2 and L positions
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. Shift lock control ECU (Shift lock control unit assembly)
  4. TCM

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the TCM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is on P or N.
The park/neutral position switch sends a signal to the TCM according to the shift lever position (R, D, 4, 3, 2 or L).
The TCM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C195731E10

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the tester, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In P or N: ON
    2. Not in P or N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In R: ON
    2. Not in R: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In D: ON
    2. Not in D: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (4 or D)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In 4 or D: ON
    2. Not in 4 or D: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (3 Range)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In 3: ON
    2. Not in 3: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (2 Range)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In 2: ON
    2. Not in 2: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (L Range)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In L: ON
    2. Not in L: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

HINT:
When the malfunction is found when the shift lever is in 3, start from *1. When the malfunction is found when the shift lever is not in 3, start from *2.


1. INSPECT PARK/NEUTRAL POSITION SWITCH*1

  1. C146745E45
    Disconnect the N1 park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Shift Lever Position
    Specified Condition
    4 (B) - 5 (L)
    P or N
    Below 1 Ω
    4 (B) - 5 (L)
    Not in P or N
    10 kΩ or higher
    1 (RL) - 2 (RB)
    R
    Below 1 Ω
    1 (RL) - 2 (RB)
    Not in R
    10 kΩ or higher
    2 (RB) - 7 (DL)
    D or 4
    Below 1 Ω
    2 (RB) - 7 (DL)
    Not in D or 4
    10 kΩ or higher
    2 (RB) - 3 (2L)
    3
    Below 1 Ω
    2 (RB) - 3 (2L)
    Not in 3
    10 kΩ or higher
    2 (RB) - 8 (LL)
    2 or L
    Below 1 Ω
    2 (RB) - 8 (LL)
    Not in 2 or L
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH
OK


2. INSPECT SHIFT LOCK CONTROL ECU*2

  1. C170575E06
    Disconnect the S43 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Shift Lever Position
    Specified Condition
    9 (NSSD) - 2 (ATD)
    D
    Below 1 Ω
    9 (NSSD) - 2 (ATD)
    4
    10 kΩ or higher
    9 (NSSD) - 3 (AT4)
    D
    10 kΩ or higher
    9 (NSSD) - 3 (AT4)
    4
    Below 1 Ω
    10 (NSSL) - 5 (AT2)
    2
    Below 1 Ω
    10 (NSSL) - 5 (AT2)
    L
    10 kΩ or higher
    10 (NSSL) - 4 (ATL)
    2
    10 kΩ or higher
    10 (NSSL) - 4 (ATL)
    L
    Below 1 Ω



NG
REPLACE SHIFT LOCK CONTROL ECU (SHIFT LOCK CONTROL UNIT ASSEMBLY)
OK


3. CHECK HARNESS AND CONNECTOR (TCM - BATTERY)
C191543E23
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Shift Lever Position
    Specified Condition
    T37-9 (R) - Body ground
    R
    11 to 14 V*
    T37-9 (R) - Body ground
    Not in R
    Below 1 V
    T37-8 (D) - Body ground
    D or 3
    11 to 14 V
    T37-8 (D) - Body ground
    Not in D or 3
    Below 1 V
    T37-13 (4) - Body ground
    4
    11 to 14 V
    T37-13 (4) - Body ground
    Not in 4
    Below 1 V
    T37-12 (3) - Body ground
    3
    11 to 14 V
    T37-12 (3) - Body ground
    Not in 3
    Below 1 V
    T37-11 (2) - Body ground
    2 or L
    11 to 14 V
    T37-11 (2) - Body ground
    Not in 2 or L
    Below 1 V
    T37-10 (L) - Body ground
    L
    11 to 14 V
    T37-10 (L) - Body ground
    Not in L
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to the illumination of the back-up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM


← P0617 Starter Relay Circuit High (from Aug 2012)P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (from Aug 2012) →